[cisco-voip] 2801 MGCP Gateway on CCM 5.0

Fri Mar 2 16:46:34 EST 2007

Why?

At no point will the CCM ever try to contact the gateway via that name.

Jonathan

On 3/2/07, Matt Slaga (US) <Matt.Slaga at us.didata.com> wrote:
>
>  Create a name for the gateway in the server's lmhosts and hosts files.
>
>
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Jonathan Charles
> *Sent:* Friday, March 02, 2007 4:34 PM
> *To:* omar parihuana
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] 2801 MGCP Gateway on CCM 5.0
>
>
>
> No, it has to be by name.
>
>
>
> CCM has no idea where the gateway is... The gateway initiates the
> registration process and tries to register with CCM using its hostname +
> domain name (make the hostname the IP and that would work). So, CCM must be
> configured with what the gateway is going to try to register with.
>
>
>
>
>
>
>
> Jonathan
>
>
>
> On 3/2/07, *omar parihuana* <omar.parihuana at gmail.com> wrote:
>
> Hi,
>
> Maybe you can disble ip domain name and use only IP address in CCM and
> Gateway,
>
> with sh ccm you must see the registration.
>
> Rgds.
>
>
>
>  On 3/2/07, *Jonathan Charles* <jonvoip at gmail.com > wrote:
>
> In CCM, you need to setup the gateway name as:
>
>
>
> GW2801.test.br <http://gw2801.test.br/>
>
>
>
> This is your hostname and your ip domain name...
>
>
>
> There is no other method.
>
>
>
> When you say it is 'active' on the gateway, that doesn't correspond to
> what it should say...
>
>
>
> If you do a:
>
>
>
> show ccm
>
>
>
> you should see it say primary and registered.
>
>
>
> And then on CCM, click on show endpoints and you should see a 'registered
> with...' if it is up.
>
>
>
>
>
> Jonathan
>
>
>
> On 2/28/07, *alsvrj* < alsvrj at superig.com.br > wrote:
>
>  Hello All,
>
> I have an 2801 connected to a Hicom 330 PBX through a ISDN PRI QSIG with
> MGCP and a CCM5.0 . I´m having a lot of problems to get the gateway
> registration on CCM.
>
> I would like to do some questions:
> 1- Is it possible to put an ISDN PRI with MGCP using QSIG signaling ?
>
> Using the show isdn status command I´m seeing MULTIPLE_FRAME_ESTABILISHED
>
> I´m seeing too with the show ccm-manager that the MGCP is Active but I´m
> not
> able to see this Gateway into the active state inside of CCM.
>
> I´m using a VWIC-1MFT-E1 card to use this ISDN PRI.
>
> 2- Is it possible to put the IP Address instead of Domain Name when I´m
> creating the 2801 Gateway ?
>
> Hey guys, I really need your help to solve this registration problem, I
> kindly ask a hand into this situation.
>
> Thanks for everything.
>
> It follows below the configuration on the Gateway:
>
> hostname GW2801
> !
> boot-start-marker
> boot system flash c2801-adventerprisek9-mz.124-6.T3.bin
> boot-end-marker
> !
> logging buffered 4096 informational
> enable secret 5 ********************
> !
> no aaa new-model
> !
> resource policy
> !
> clock timezone UTC -3
> network-clock-participate wic 2
> network-clock-select 1 E1 0/2/0
> ip cef
> !
> !
> !
> !
> ip tcp synwait-time 13
> no ip domain lookup
> ip domain name test.br
> ip name-server *.*.*.*
> ip name-server *.*.*.*
> ip name-server *.*.*.*
> !
> isdn switch-type primary-qsig
> isdn logging
> !
> voice-card 0
> dsp services dspfarm
> !
> !
> voice call carrier capacity active
> !
> !
> voice class codec 1
> codec preference 1 g711ulaw
> codec preference 2 g729r8 bytes 40
> !
> !
> !
> voice class h323 1
> h225 timeout tcp establish 3
> !
> crypto configuration
> !
> controller E1 0/2/0
> framing NO-CRC4
> line-termination 75-ohm
> pri-group timeslots 1-31 service mgcp
> !
> !
> interface FastEthernet0/0
> ip address *.*.*.* *.*.*.*
> speed 100
> full-duplex
> no cdp enable
> h323-gateway voip bind srcaddr *.*.*.*
> !
> interface FastEthernet0/1
> no ip address
> shutdown
> duplex auto
> speed auto
> no cdp enable
> !
> interface Serial0/1/0
> no ip address
> shutdown
> clock rate 2000000
> no cdp enable
> !
> interface Serial0/2/0:15
> no ip address
> no ip proxy-arp
> encapsulation hdlc
> isdn switch-type primary-qsig
> isdn overlap-receiving
> isdn incoming-voice voice
> isdn supp-service name calling
> isdn bind-l3 ccm-manager
> isdn negotiate-bchan
> isdn bchan-number-order ascending
> isdn sending-complete
> no cdp enable
> !
> ip route 0.0.0.0 0.0.0.0 *.*.*.*
> !
> !
> ip http server
> ip http secure-server
> !
> logging *.*.*.*
> access-list 1 permit *.*.*.*
> access-list 1 permit *.*.*.*
> dialer-list 1 protocol ip permit
> snmp-server community voip RW 1
> snmp-server community ext0399 RW 1
> snmp-server community sw0399 RW 1
> disable-eadi
> no cdp run
> !
> control-plane
> !
> voice-port 0/2/0:15
> !
> ccm-manager mgcp
> ccm-manager music-on-hold
> ccm-manager config server *.*.*.*
> ccm-manager config
> !
> mgcp
> mgcp call-agent *.*.*.* 2427 service-type mgcp version 0.1
> mgcp dtmf-relay voip codec all mode out-of-band
> mgcp rtp unreachable timeout 1000 action notify
> mgcp modem passthrough voip mode nse
> mgcp package-capability rtp-package
> no mgcp package-capability res-package
> mgcp package-capability sst-package
> no mgcp package-capability fxr-package
> mgcp package-capability pre-package
> no mgcp timer receive-rtcp
> mgcp sdp simple
> mgcp fax t38 inhibit
> mgcp rtp payload-type g726r16 static
> !
> mgcp profile default
> !
> !
> dial-peer cor custom
> !
> !
> !
> dial-peer voice 1 pots
> service mgcpapp
> port 0/2/0:15
> !
> !
> !
> line con 0
> exec-timeout 0 0
> password 7 *****************
> logging synchronous
> login
> line aux 0
> exec-timeout 0 0
> password 7 *****************
> logging synchronous
> login
> line vty 0 4
> exec-timeout 0 0
> password 7 **************
> logging synchronous
> login
> !
> scheduler allocate 20000 1000
> ntp clock-period 17180079
> ntp server *.*.*.*
> !
> webvpn context Default_context
> ssl authenticate verify all
> !
> no inservice
> end
>
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
> --
> Omar E.P.T
> -----------------
> Certified Networking Professionals make better Connections!
>
> http://omarept.blogspot.com/
>
>   Usysnet Corp
> Open Source Solutions
> www.usysnet.com.pe
>
>
>
> ------------------------------
>
> *Disclaimer: This e-mail communication and any attachments may contain
> confidential and privileged information and is for use by the designated
> addressee(s) named above only. If you are not the intended addressee, you
> are hereby notified that you have received this communication in error and
> that any use or reproduction of this email or its contents is strictly
> prohibited and may be unlawful. If you have received this communication in
> error, please notify us immediately by replying to this message and deleting
> it from your computer. Thank you. *
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070302/f1c12ad4/attachment.html 