[cisco-voip] 2801 MGCP Gateway on CCM 5.0

Fri Mar 2 16:39:25 EST 2007

Create a name for the gateway in the server's lmhosts and hosts files.

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jonathan Charles
Sent: Friday, March 02, 2007 4:34 PM
To: omar parihuana
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] 2801 MGCP Gateway on CCM 5.0

No, it has to be by name.

CCM has no idea where the gateway is... The gateway initiates the registration process and tries to register with CCM using its hostname + domain name (make the hostname the IP and that would work). So, CCM must be configured with what the gateway is going to try to register with. 

Jonathan

On 3/2/07, omar parihuana <omar.parihuana at gmail.com> wrote: 

Hi,

Maybe you can disble ip domain name and use only IP address in CCM and Gateway,

with sh ccm you must see the registration. 

Rgds. 

On 3/2/07, Jonathan Charles <jonvoip at gmail.com > wrote: 

In CCM, you need to setup the gateway name as:

GW2801.test.br <http://gw2801.test.br/> 

This is your hostname and your ip domain name...

There is no other method.

When you say it is 'active' on the gateway, that doesn't correspond to what it should say...

If you do a:

show ccm

you should see it say primary and registered.

And then on CCM, click on show endpoints and you should see a 'registered with...' if it is up.

Jonathan

On 2/28/07, alsvrj < alsvrj at superig.com.br <mailto:alsvrj at superig.com.br> > wrote: 

	Hello All,

	I have an 2801 connected to a Hicom 330 PBX through a ISDN PRI QSIG with 
	MGCP and a CCM5.0 . I´m having a lot of problems to get the gateway
	registration on CCM.

	I would like to do some questions: 
	1- Is it possible to put an ISDN PRI with MGCP using QSIG signaling ?

	Using the show isdn status command I´m seeing MULTIPLE_FRAME_ESTABILISHED 

	I´m seeing too with the show ccm-manager that the MGCP is Active but I´m not 
	able to see this Gateway into the active state inside of CCM.

	I´m using a VWIC-1MFT-E1 card to use this ISDN PRI.

	2- Is it possible to put the IP Address instead of Domain Name when I´m 
	creating the 2801 Gateway ? 

	Hey guys, I really need your help to solve this registration problem, I
	kindly ask a hand into this situation.

	Thanks for everything.

	It follows below the configuration on the Gateway: 

	hostname GW2801 
	!
	boot-start-marker
	boot system flash c2801-adventerprisek9-mz.124-6.T3.bin
	boot-end-marker
	!
	logging buffered 4096 informational
	enable secret 5 ********************
	!
	no aaa new-model 
	!
	resource policy
	!
	clock timezone UTC -3
	network-clock-participate wic 2
	network-clock-select 1 E1 0/2/0
	ip cef
	!
	!
	!
	!
	ip tcp synwait-time 13
	no ip domain lookup
	ip domain name test.br <http://test.br/> 
	ip name-server *.*.*.*
	ip name-server *.*.*.*
	ip name-server *.*.*.*
	!
	isdn switch-type primary-qsig 
	isdn logging
	!
	voice-card 0
	dsp services dspfarm
	!
	!
	voice call carrier capacity active 
	!
	!
	voice class codec 1
	codec preference 1 g711ulaw
	codec preference 2 g729r8 bytes 40
	!
	!
	!
	voice class h323 1
	h225 timeout tcp establish 3
	!
	crypto configuration 
	!
	controller E1 0/2/0 
	framing NO-CRC4
	line-termination 75-ohm
	pri-group timeslots 1-31 service mgcp
	!
	!
	interface FastEthernet0/0
	ip address *.*.*.* *.*.*.*
	speed 100
	full-duplex
	no cdp enable 
	h323-gateway voip bind srcaddr *.*.*.* 
	!
	interface FastEthernet0/1
	no ip address
	shutdown
	duplex auto
	speed auto
	no cdp enable
	!
	interface Serial0/1/0
	no ip address
	shutdown
	clock rate 2000000 
	no cdp enable
	!
	interface Serial0/2/0:15 
	no ip address
	no ip proxy-arp
	encapsulation hdlc
	isdn switch-type primary-qsig
	isdn overlap-receiving
	isdn incoming-voice voice
	isdn supp-service name calling 
	isdn bind-l3 ccm-manager
	isdn negotiate-bchan 
	isdn bchan-number-order ascending
	isdn sending-complete
	no cdp enable
	!
	ip route 0.0.0.0 <http://0.0.0.0/>  0.0.0.0 <http://0.0.0.0/>  *.*.*.*
	!
	!
	ip http server
	ip http secure-server
	!
	logging *.*.*.*
	access-list 1 permit *.*.*.*
	access-list 1 permit *.*.*.*
	dialer-list 1 protocol ip permit
	snmp-server community voip RW 1 
	snmp-server community ext0399 RW 1
	snmp-server community sw0399 RW 1
	disable-eadi
	no cdp run
	!
	control-plane
	!
	voice-port 0/2/0:15
	!
	ccm-manager mgcp
	ccm-manager music-on-hold
	ccm-manager config server *.*.*.* 
	ccm-manager config
	!
	mgcp
	mgcp call-agent *.*.*.* 2427 service-type mgcp version 0.1
	mgcp dtmf-relay voip codec all mode out-of-band
	mgcp rtp unreachable timeout 1000 action notify
	mgcp modem passthrough voip mode nse 
	mgcp package-capability rtp-package
	no mgcp package-capability res-package
	mgcp package-capability sst-package
	no mgcp package-capability fxr-package
	mgcp package-capability pre-package
	no mgcp timer receive-rtcp 
	mgcp sdp simple
	mgcp fax t38 inhibit
	mgcp rtp payload-type g726r16 static
	!
	mgcp profile default
	!
	!
	dial-peer cor custom
	!
	!
	!
	dial-peer voice 1 pots
	service mgcpapp
	port 0/2/0:15 
	!
	!
	!
	line con 0
	exec-timeout 0 0
	password 7 *****************
	logging synchronous
	login
	line aux 0
	exec-timeout 0 0
	password 7 *****************
	logging synchronous
	login
	line vty 0 4 
	exec-timeout 0 0
	password 7 **************
	logging synchronous
	login
	!
	scheduler allocate 20000 1000
	ntp clock-period 17180079
	ntp server *.*.*.*
	!
	webvpn context Default_context
	ssl authenticate verify all 
	!
	no inservice
	end

	_______________________________________________
	cisco-voip mailing list
	cisco-voip at puck.nether.net
	https://puck.nether.net/mailman/listinfo/cisco-voip 

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip 

-- 
Omar E.P.T
-----------------
Certified Networking Professionals make better Connections!

http://omarept.blogspot.com/

  Usysnet Corp
Open Source Solutions
www.usysnet.com.pe <http://www.usysnet.com.pe/>  

-----------------------------------------
Disclaimer:

This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only.  If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful.  If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070302/7fe64ffe/attachment-0001.html 