[cisco-voip] CCM & PBX via Qsig

[Dietmar]

Hi,

have you set the "Channel IE Type" to "Continuous Number" on the gateway 
configuration site? The protocol on the Siemens should be set to PSS1V2.


Dietmar


On Sunday 25 March 2007 12:48:28 Lemon wrote:
> Hi,
>
> I have the following setup:
>
> A Siemens PBX connecting to a CallManager via Qsig (mgcp controlled)
>
> and
>
> the CCM connecting to PSTN via PRI (mgcp controlled)
>
> Calls to and from CCM works fine (inbound and outbound)
> Calls to and from PBX works fine (inbound and outbound)
> Calls from CCM to PBX works fine
> Calls from PBX to CCM does not work
>
> My D-channel towards the PBX looks like this:
> !
> interface Serial1/0:15
>  no ip address
>  encapsulation hdlc
>  isdn switch-type primary-qsig
>  isdn overlap-receiving T302 2000
>  isdn incoming-voice voice
>  isdn bind-l3 ccm-manager
>  isdn sending-complete
>  no cdp enable
> end
> !
>
> and debug isdn q931 gives the following:
>
> 01260: Mar 25 11:13:42.699 SAST: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8
> callref = 0x0001
>         Sending Complete
>         Bearer Capability i = 0x9090A3
>                 Standard = CCITT
>                 Transfer Capability = 3.1kHz Audio
>                 Transfer Mode = Circuit
>                 Transfer Rate = 64 kbit/s
>         Channel ID i = 0xA98381
>                 Exclusive, Channel 1
>         Facility i =
> 0x91AA068001008201008B0100A10D02017D06042B0C092903020780
>         Facility i =
> 0x91AA068001008201008B0102A11302017E02013B300B30090A01050A01040A0103
>         Facility i =
> 0x91AA068001008201008B0100A11402017F06042B0C09008009524543455054494F4E
>         Progress Ind i = 0x8183 - Origination address is non-ISDN
>         Calling Party Number i = 0x0183, '70008'
>                 Plan:ISDN, Type:Unknown
>         Called Party Number i = 0x89, '70051'
>                 Plan:Private, Type:Unknown
>         Locking Shift to Codeset 5
>         Codeset 5 IE 0x32  i = 0x81
> 001261: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd =
> 8  callref = 0x8001
>         Channel ID i = 0xA98381
>                 Exclusive, Channel 1
> 001262: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> FACILITY pd = 8
> callref = 0x8001
>         Facility i = 0x9FAA06800100820100A40602017E800100
> 001263: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> ALERTING pd = 8
> callref = 0x8001
>         Facility i =
> 0x9FAA06800100820100A112020101020101800A4D6172636F204465656E
>         Progress Ind i = 0x8088 - In-band info or appropriate now available
> 001264: Mar 25 11:13:42.759 SAST: ISDN Se1/0:15 Q931: RX <- STATUS pd = 8
> callref = 0x0001
>         Cause i = 0x81E41C - Invalid information element contents
>         Call State i = 0x03
> 001265: Mar 25 11:13:42.771 SAST: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd =
> 8  callref = 0x8001
>         Cause i = 0x80E2 - Message not compatible with call state or not
> implemented
> 001266: Mar 25 11:13:43.075 SAST: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8
> callref = 0x0001
> 001267: Mar 25 11:13:43.099 SAST: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP pd
> = 8  callref = 0x8001
>
>
>
> Any ideas? Where to look?
>
> Thnx
>
> Charl



-- 
E-Mail: db7td at gmx.de