[cisco-voip] Reset an FXO port

[Jorge Evangelista]

Hi,

You can use    clear voice port 0/0/0


On 4/30/07, Clouse, Chris <chris.clouse at berbee.com> wrote:
>
>
>
> Can you post the port configuration?
>
>
>
> -Christopher
>
>
>
>
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of
> Todd Franklin
> Sent: Monday, April 30, 2007 1:17 PM
> To: Adam; cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] Reset an FXO port
>
>
>
>
> Yeah I did that.  But still no go.
> Here is the sho voice port 0/0/0 command output:
>
> ho voice port 0/0/0
>
> Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
>  Type of VoicePort is FXO
>  Operation State is DORMANT
>  Administrative State is UP
>  The Last Interface Down Failure Cause is Administrative Shutdown
>  Description is 555-123-4567
>  Noise Regeneration is enabled
>  Non Linear Processing is enabled
>  Non Linear Mute is disabled
>  Non Linear Threshold is -21 dB
>  Music On Hold Threshold is Set to -38 dBm
>  In Gain is Set to 0 dB
>  Out Attenuation is Set to 3 dB
>  Echo Cancellation is enabled
>  Echo Cancellation NLP mute is disabled
>  Echo Cancellation NLP threshold is -21 dB
>  Echo Cancel Coverage is set to 48 ms
>  Echo Cancel worst case ERL is set to 6 dB
>  Playout-delay Mode is set to adaptive
>  Playout-delay Nominal is set to 60 ms
>  Playout-delay Maximum is set to 250 ms
>  Playout-delay Minimum mode is set to default, value 40 ms
>  Playout-delay Fax is set to 300 ms
>  Connection Mode is plar
>  Connection Number is 2002
>  Initial Time Out is set to 10 s
>  Interdigit Time Out is set to 10 s
>  Call Disconnect Time Out is set to 60 s
>  Ringing Time Out is set to 180 s
>  Wait Release Time Out is set to 30 s
>  Companding Type is u-law
>  Region Tone is set for US
>
>  Analog Info Follows:
>  Currently processing none
>  Maintenance Mode Set to None (not in mtc mode)
>  Number of signaling protocol errors are 0
>  Impedance is set to 600r Ohm
>  Station name None, Station number None
>  Translation profile (Incoming):
>  Translation profile (Outgoing):
>
>  Voice card specific Info Follows:
>  Signal Type is loopStart
>  Battery-Reversal is enabled
>  Number Of Rings is set to 1
>  Supervisory Disconnect is signal
>  Answer Supervision is inactive
>  Hook Status is On Hook
>  Ring Detect Status is inactive
>  Ring Ground Status is inactive
>  Tip Ground Status is inactive
>  Dial Out Type is dtmf
>  Digit Duration Timing is set to 100 ms
>  InterDigit Duration Timing is set to 100 ms
>  Pulse Rate Timing is set to 10 pulses/second
>  InterDigit Pulse Duration Timing is set to 750 ms
>  Percent Break of Pulse is 60 percent
>  GuardOut timer is 2000 ms
>  Minimum ring duration timer is 125 ms
>  Hookflash-in Timing is set to 600 ms
>  Hookflash-out Timing is set to 500 ms
>  Supervisory Disconnnct Timing is set to 350 ms
>
> I think I am missing something basic.  This has happened before and the only
> way to fix it was to reboot the 2801.
>
> Todd
>
>
> On 4/30/07, Adam <cisco at adman.net> wrote:
>
> How about a 'shutdown' followed by 'no shutdown' in the voice-port
> configuration?
>
> -Adam
>
> On 4/30/07, Todd Franklin <toddnh65 at gmail.com> wrote:
> > Apparently my FXO port is hung internally.  I can't easily reboot this box
> > since it has my PRI on it as well.
> > Is there a command to just reset the FXO port?  Right now I have my telco
> > busying it out so it will fall over to the next line (which comes in on
> the
> > PRI).
> >
> > Thanks anyone!
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>


-- 
"The network is the computer"