[cisco-voip] RV: layer 2 varies between TEI_ASSIGNED and AWAITINGESTABLISHEMENT
Jonathan Charles
jonvoip at gmail.com
Sat Nov 24 11:25:22 EST 2007
With this many errors on the T1 Carrier, the first step is a telco
ticket... get them to run patterns from the DAX to the CSU.
If they run clean to your SmartJack and fail to the CSU, then your
problem is inside wiring.
In all likelihood you have a bad repeater in the field.
Jonathan
On Nov 21, 2007 1:04 PM, zohaib shabir <zohaibshabir at gmail.com> wrote:
> i had the similar issue somewhat closer to what you are saying. Initially
> PBX integration is tested with 3845 router, but when tested with 2811 router
> the problem of LCV and PCV came up, resulting in E1 link up and down. then
> what i did was to put the E1 controller in NM-hd2ve module rather than
> directly in HWIC solved the problem for me. however it sounds quite amazing
> but it happenend andd with same IOS version you are having.
>
>
>
> On 11/21/07, Ryan Ratliff <rratliff at cisco.com> wrote:
> > Including cisco-voip list since Ralil is having issues sending.
> >
> > The first that jumps out at me is the linecode violations. Have you
> > tried changing this setting (it is not defined in your config below)
> > to see if you can clear those up?
> >
> > #sh controllers e1
> > E1 0/2/0 is up.
> > Applique type is Channelized E1 - balanced
> > No alarms detected.
> > alarm-trigger is not set
> > Version info Firmware: 20060707, FPGA: 13, spm_count = 0
> > Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
> > CRC Threshold is 320. Reported from firmware is 320.
> > Data in current interval (286 seconds elapsed):
> > 1046 Line Code Violations, 0 Path Code Violations
> > 1 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 1 Degraded Mins
> > 2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 170
> > Unavail Secs
> > Total Data (last 24 hours)
> > 0 Line Code Violations, 0 Path Code Violations,
> > 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
> > 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400
> > Unavail Secs
> > -Ryan
> >
> > On Nov 21, 2007, at 12:06 PM, Ralil Ayancan Guillermo ((Contratista-
> > Teniente)) wrote:
> >
> >
> > Please help me...
> > Please can you send to mail list my cuestion.
> > I don't have email to list cisco voip, I am subscribed and server send
> > me this error.
> >
> > Thanks.
> >
> > -----Mensaje original-----
> > De: cisco-voip-bounces at puck.nether.net
> > [mailto:cisco-voip-bounces at puck.nether.net] En nombre de
> > cisco-voip-owner at puck.nether.net
> > Enviado el: martes, 20 de noviembre de 2007 17:35
> > Para: Ralil Ayancan Guillermo (Contratista-Teniente)
> > Asunto: RE: layer 2 varies between TEI_ASSIGNED and
> > AWAITINGESTABLISHEMENT
> >
> > Greetings,
> >
> > It does not appear that you are currently subscribed as a member of
> > this list. You must be a subcribed member posting from the address
> > that you receive mail to for posting to work.
> >
> > We send you monthly E-Mails reminding you of your e-mail address you
> > are subscribed to the list with, including the password that you can
> > use to change your list settings.
> >
> > You can get a password reminder here:
> >
> > http://puck.nether.net/mailman/options/cisco-voip
> >
> >
> > From: "Ralil Ayancan Guillermo \(Contratista-Teniente\)"
> > <GRalil at contratistas.codelco.cl>
> > Date: November 20, 2007 3:22:28 PM EST
> > To: <cisco-voip at puck.nether.net >
> > Cc: "Ryan Ratliff" <rratliff at cisco.com>
> > Subject: RE: layer 2 varies between TEI_ASSIGNED and
> > AWAITINGESTABLISHEMENT
> >
> >
> >
> > Hello dears:
> > My problem is that. I can´t connect E1 (direct from pbx) to router
> > cisco 2801 with IOS Version 12.4(3g).
> > The layer 1 is ACTIVE STATE but the layer 2 change between
> > TEI_ASSIGNED and AWAITING ESTABLISHEMENT.
> > I test with different encapsulations (ppp, hdlc) and different
> > signalling (qsig, net5), in other router with identical hardware,
> > configuration and IOS connect without problems and automatically (The
> > PBX or cable is not the problem)
> > Nothing change if reload the router, reinit interface serial0/2/0:15
> > or e1, clear counter, etc.
> > When I debug q921 on I don't receive Rx, only TX out from cisco 2801.
> >
> > How know if the card VWIC in the router is the true problem?
> > Thanks.
> >
> > (sorry for my English)
> >
> >
> >
> > debug
> >
> > *Nov 20 14:23:12.499: ISDN Se0/2/0:15 Q921: L2_EstablishDataLink:
> > sending SABME
> > *Nov 20 14:23:12.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:13.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:14.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:15.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:21.499: ISDN Se0/2/0:15 Q921: L2_EstablishDataLink:
> > sending SABME
> > *Nov 20 14:23:21.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:22.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:23.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> > *Nov 20 14:23:24.499: ISDN Se0/2/0:15 Q921: User TX -> SABMEp sapi=0
> > tei=0
> >
> > ....
> > !
> > controller E1 0/2/0
> > framing NO-CRC4
> > pri-group timeslots 1-31
> > !
> > ....
> > interface Serial0/2/0:15
> > no ip address
> > encapsulation ppp
> > isdn switch-type primary-qsig
> > isdn timer T310 10000
> > isdn overlap-receiving
> > isdn incoming-voice modem
> > isdn T309-enable
> > isdn negotiate-bchan
> > isdn bchan-number-order ascending
> > no cdp enable
> >
> >
> >
> > #sh isdn status
> > Global ISDN Switchtype = primary-net5
> > ISDN Serial0/2/0:15 interface
> > dsl 0, interface ISDN Switchtype = primary-net5
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED <->
> > AWAITING ESTABLISHEMENT
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Active dsl 0 CCBs = 0
> > The Free Channel Mask: 0x00000000
> > Number of L2 Discards = 0, L2 Session ID = 170
> > Total Allocated ISDN CCBs = 0
> > #
> >
> > #sh controllers e1
> > E1 0/2/0 is up.
> > Applique type is Channelized E1 - balanced
> > No alarms detected.
> > alarm-trigger is not set
> > Version info Firmware: 20060707, FPGA: 13, spm_count = 0
> > Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
> > CRC Threshold is 320. Reported from firmware is 320.
> > Data in current interval (286 seconds elapsed):
> > 1046 Line Code Violations, 0 Path Code Violations
> > 1 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 1 Degraded Mins
> > 2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 170
> > Unavail Secs
> > Total Data (last 24 hours)
> > 0 Line Code Violations, 0 Path Code Violations,
> > 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
> > 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 86400
> > Unavail Secs
> >
> >
> >
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
>
>
>
> --
> Regards,
> Zohaib Shabir
> Network Engineer(Voice)
> DWP Group, TECH Division Karachi
> Ph:+92-302-8232689
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
More information about the cisco-voip
mailing list