[cisco-voip] Inbound Caller ID NAME

[CarlosOrtiz at bayviewfinancial.com]

Not in general but for this particular feature my SE sent an email stating 
the following:

"Carlos,
 
H.323 calling name is a feature that was released in IOS 12.4.11XW and 
will be integrated into the mainline release 12.15(1)T.  This particular 
release has not been "officially" recommended in the "golden bridge" IP 
telephony matrix for IOS gateways.  Your best option to deliver this 
feature to the business would be to go with the latest revision of the XW 
train available on CCO currently XW3.  The fact that this release is not 
included in the IP telephony matrix as a recommended release for gateways 
does not mean is a bad release; it should not create any problems for you 
but realistically it could as the introduction of new features some times 
introduce new issues.  I would recommend that you test it on a single site 
for a couple of weeks and if all goes well then deploy it to additional 
sites."






"Linsemier, Matthew" <MLinsemier at apcapital.com> 
Sent by: cisco-voip-bounces at puck.nether.net
09/27/2007 10:45 AM

To
"Justin Steinberg" <jsteinberg at gmail.com>, 
<CarlosOrtiz at bayviewfinancial.com>
cc
cisco-voip at puck.nether.net
Subject
Re: [cisco-voip] Inbound Caller ID NAME






Does anyone know when features like this transfer out of a specialized XW 
release and are added to the general or T train of code?
 
From: cisco-voip-bounces at puck.nether.net 
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Justin Steinberg
Sent: Thursday, September 27, 2007 9:03 AM
To: CarlosOrtiz at bayviewfinancial.com
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Inbound Caller ID NAME
 
H.323 NAME Display feature in 12.4(11) XW
http://www.cisco.com/en/US/products/ps6706/prod_release_note09186a0080837f1a.html#wp329995
 
On 9/20/07, CarlosOrtiz at bayviewfinancial.com < 
CarlosOrtiz at bayviewfinancial.com> wrote:

Can anyone verify Robert's suggested IOS version for inbound Caller ID to 
work on H.323?  What additional commands on the gateway and Call Mgr 
config are needed? 

Carlos 



Robert Kulagowski <rkulagow at gmail.com> 
09/14/2007 11:30 AM 


To
CarlosOrtiz at bayviewfinancial.com 
cc
cisco-voip at puck.nether.net 
Subject
Re: [cisco-voip] Inbound Caller ID NAME
 








> I was looking through the archives and it seems that to get inbound 
> caller ID NAME to work you MUST:
> 
> 1) Use MGCP
> 2) Enable NI2 protocol
> 
> Is this still the case?  Did I miss anything else?

Check the archives a little more! :)

We just discussed this not too long ago.

You can use H.323: either use the cname tcl script that was written by 
David Zilk or the IOS that has this built-in.  12.4.11XU?

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net 
https://puck.nether.net/mailman/listinfo/cisco-voip
 

CONFIDENTIALITY STATEMENT
This communication and any attachments are CONFIDENTIAL and may be 
protected by one or more legal privileges. It is intended solely for the 
use of the addressee identified above. If you are not the intended 
recipient, any use, disclosure, copying or distribution of this 
communication is UNAUTHORIZED. Neither this information block, the typed 
name of the sender, nor anything else in this message is intended to 
constitute an electronic signature unless a specific statement to the 
contrary is included in this message. If you have received this 
communication in error, please immediately contact me and delete this 
communication from your computer. Thank you. 
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20070927/ca7229df/attachment.html