[cisco-voip] Append LD Access code on outbound call

[Jason Aarons (US)]

Have telco remove the 3-digit code and configure FAC in CallManager?  Or
is telco providing some sort of billing reports?

 

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wes Sisk
Sent: Friday, July 11, 2008 9:51 AM
To: Carter, Bill
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Append LD Access code on outbound call

 

not likely to be possible.  most access codes require inband dtmf.  note
this is distinctly separate from the digits send on the isdn d-ch to
establish the call.

only likely way would be a custom IPCCX/IVR, TCL, or CUEA script that:
1. sends the inital setup with called party number
2. waits a period of time, or even better, does tone detection to
determine when the telco prompts for access code
3. sends the access code as inband DTMF
4. connects the calling/called party numbers

Customers i've worked with in the past were not interested in this much
work for a single special user.  they usually dedicated 1 pots line to
allow that person outbound calling.  remove the LD codes from the pots
line and configure CSS so only the special user can use that pots line.

/Wes

Carter, Bill wrote: 

Telco requires a 3-digit access code for long distance calls. Customer
would like to NOT have to dial a code when faxing to a LD number. Is
this possible??

 

Background:

PSTN connection is PRI

Telco says LD code required for all outbound calls. (can't disable based
on calling party #)

GW is H323

 

 

 

Gateway Attempts:

On the gateway I tried a standard dial peer with  "translate-outgoing
called". I tried post-pending a ,022 to the string (, is supposed to
insert a pause and 022 is the telco access code).

 

voice translation-rule 10

 rule 1 /^\#\(1[2-9]..[2-9]......\)/ /\1\2,022/

 

test voice translation-rule 10 #14085551212

Matched with rule 1

Original number: #14085551212   Translated number: 14085551212,022

Original number type: none      Translated number type: none

Original number plan: none      Translated number plan: none

 

dial-peer voice 300 pots

 description -- POTS Dial peer to route calls out PRI --

 destination-pattern #1[2-9]..[2-9]......

 translate-outgoing called 10

 incoming called-number .

 direct-inward-dial

 port 0/1/0:23

 prefix 1

 

I tried "forward-digits extra" which is supposed to send any digits
longer than the length of the destination-pattern. Didn't work.

 

CallManager Attempts:

I also tried the CallManager translation-pattern route:

 

Translation Pattern

91[2-9]XX[2-9]XXXXXX

Calling Party Transformation Mask

XXXXXXXXXXXX022

DNA analysis gives the following

Dialed number 914085551212

Result ???714085551022

 

 

 

 

Bill Carter

Sr Business Communications Analyst

Sentinel Technologies, Inc

217.391.5015

 

 


________________________________



 
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
  



-----------------------------------------
Disclaimer:

This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only.  If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful.  If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20080711/5900d14c/attachment.html>