[cisco-voip] did/fxs config help

[Ryan West]

Try

voice-port 0/1/0
 signal did immediate-start
 input gain 4


dial-peer voice 150 pots
 incoming called-number 5552340
 port 0/1/0
!

debug voip ccapi inout
term mon

watch for dial-peer matching and watch for failures

If you're trying to translate to 1010, you'll need a translation pattern to do so or a configure a secondary on the ephone-dn that matches 5552340.

-ryan
-----Original Message-----
From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Dan Letkeman
Sent: Wednesday, July 23, 2008 7:45 PM
To: Paul; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] did/fxs config help

Ok, so this is what I have so far, but I still get a busy signal.

voice-port 0/1/0
 signal did wink-start
 input gain 4


dial-peer voice 150 pots
 incoming called-number 5552340
 port 0/1/0
!
!
num-exp 2340 1010

You were saying something about an ephone-dn?

Dan.

On Wed, Jul 23, 2008 at 5:39 PM, Paul <asobihoudai at yahoo.com> wrote:
> Dan,
>
> What you need is to configure a dial-peer with 'incoming called-number .' and configure your ephone-DNs. Every created ephone-DN creates a virtual dial-peer that is associated with the ephone that you assign this ephone-DN to.
>
> Paul
>
>
>
> ----- Original Message ----
> From: Dan Letkeman <danletkeman at gmail.com>
> To: Craig Staffin <craig at staffin.org>; cisco-voip at puck.nether.net
> Sent: Wednesday, July 23, 2008 3:06:58 PM
> Subject: Re: [cisco-voip] did/fxs config help
>
> Ok.  I think I need to configure both the dial peer's and the
> called-number.  Do you have an example config or some links to
> configure this?
>
> Thanks,
> Dan.
>
> On Wed, Jul 23, 2008 at 6:46 AM, Craig Staffin <craig at staffin.org> wrote:
>> Moataz,
>> Not always true the FXS ports are actually used for analog DID trunks.
>> As far as the problem do you have dial peers on the router?  You will need
>> both an inacoming dial peer and outgoing OR  a phone with that DN on it
>> THe incoming must have incoming-called-number . (or some form of the number)
>> Craig
>>
>> On Wed, Jul 23, 2008 at 4:43 AM, Moataz Mamdouh <moataz_mmdh at yahoo.com>
>> wrote:
>>>
>>> u call from FXS!!!!
>>> --- On Tue, 7/22/08, Dan Letkeman <danletkeman at gmail.com> wrote:
>>>
>>> From: Dan Letkeman <danletkeman at gmail.com>
>>> Subject: [cisco-voip] did/fxs config help
>>> To: cisco-voip at puck.nether.net
>>> Date: Tuesday, July 22, 2008, 9:51 PM
>>>
>>> Hello,
>>>
>>> I'm trying to setup a couple of did lines into a cme router.
>>> Currently the voice ports look like this:
>>>
>>> voice-port 0/1/1
>>>  signal did wink-start
>>>
>>>  input gain 4
>>>
>>> and I have setup the num-exp commands:
>>>
>>> num-exp 2346 1002
>>> num-exp 2341 1011
>>> num-exp 2347 1020
>>>
>>> I'm guessing I need a dial-peer?
>>>
>>> When I call the number 5552340 all I get is a busy signal.
>>>
>>>
>>> Where should I go from
>>>  here?
>>>
>>> Thanks,
>>> Dan.
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>
>>
>>
>> --
>> Craig Staffin
>> Craig at staffin.org
>> (H) 262-437-7313
>> (C) 262-613-6003
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
>
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip