[cisco-voip] i get busy error w/ isdn incoming calls.

Tue May 13 08:13:10 EDT 2008

Provider sends 3 digits as you mentioned.

I had already written translation patterns as you mentioned but my real problems was the partitions.

Translation pattern-DN partition mismatch was the real problem.

Jason, Zoltan and Chris, many thanks for quick responses, really helped.

Best,

Aykut

   _____  

From: Jason Aarons (US) [mailto:jason.aarons at us.didata.com] 
Sent: Monday, May 12, 2008 5:13 PM
To: Aykut NURAT; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] i get busy error w/ isdn incoming calls.

Provider is only sending 300, do you have a match in CallManager? For a test put a Line X on phone with 300 in none partition.

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Aykut NURAT
Sent: Monday, May 12, 2008 10:00 AM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] i get busy error w/ isdn incoming calls.

Hi Everyone,

I have a problem with an mgcp gateway.

I can call from internal ip phones to pstn numbers without a problem. Hence my mgcp gw is up&running and registered to my CCM 6.1. I have an ISDN PRI e1 and it is also up and there is no problem w/ outgoing calls as mentioned before.

But i have problems w/ incoming calls from pstn to internal phones.

Because this is an urgent situtaion just wanted take your opinions before making a widened search.

Here is isdn q921 and q931 output.

When i call from outside pstn to internal numbers i get the below output:

*May 12 13:36:09.943: ISDN Se0/2/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=1

*May 12 13:36:09.943: ISDN Se0/2/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=1

*May 12 13:36:09.947: ISDN Se0/2/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=1

*May 12 13:36:13.979: ISDN Se0/2/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=1 nr=1

*May 12 13:36:13.979: ISDN Se0/2/0:15 Q931: SETUP pd = 8  callref = 0x0208 

        Sending Complete 

        Bearer Capability i = 0x8090A3 

                Standard = CCITT 

                Transfer Capability = Speech  

                Transfer Mode = Circuit 

                Transfer Rate = 64 kbit/s 

        Channel ID i = 0xA98381 

                Exclusive, Channel 1 

        Progress Ind i = 0x8283 - Origination address is non-ISDN  

        Display i = 'INTERNATIONAL' 

        Calling Party Number i = 0x0083, '00902123473265' 

                Plan:Unknown, Type:Unknown 

        Called Party Number i = 0x81, '300' 

                Plan:ISDN, Type:Unknown

*May 12 13:36:13.983: ISDN Se0/2/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=2

*May 12 13:36:17.979: ISDN Se0/2/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=2 nr=1

*May 12 13:36:17.979: ISDN Se0/2/0:15 Q931: SETUP pd = 8  callref = 0x0208 

        Sending Complete 

        Bearer Capability i = 0x8090A3 

                Standard = CCITT 

                Transfer Capability = Speech  

                Transfer Mode = Circuit 

                Transfer Rate = 64 kbit/s 

        Channel ID i = 0xA98381 

                Exclusive, Channel 1 

        Progress Ind i = 0x8283 - Origination address is non-ISDN  

        Display i = 'INTERNATIONAL' 

        Calling Party Number i = 0x0083, '00902123473265' 

                Plan:Unknown, Type:Unknown 

        Called Party Number i = 0x81, '300'  (this line came to me weird i get this when i call 268 87300 , but if i call 268 87324 i get this as 324. As if provider sending only 3 digits??)

                Plan:ISDN, Type:Unknown

*May 12 13:36:17.983: ISDN Se0/2/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=3

*May 12 13:36:21.979: ISDN Se0/2/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=3 nr=1

*May 12 13:36:21.979: ISDN Se0/2/0:15 Q931: DISCONNECT pd = 8  callref = 0x0208 

        Cause i = 0x82E6 - Recovery on timer expiry (error code was “Cause i = 0x8081 - Unallocated/unassigned number” but it changed after i made some changes)

*May 12 13:36:21.979: ISDN Se0/2/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=4

xxx_MainCampVGw#

I have tried many pri settings on my CCM. I tried decreasing significant digits coming from pri to 4 and wrote translation patterns to internal numbers but no way.

Any comments and suggestions will be highly appreciated. 

Best,

Aykut

No virus found in this outgoing message.
Checked by AVG.
Version: 7.5.524 / Virus Database: 269.23.9/1418 - Release Date: 5/6/2008 5:17 PM

   _____  

Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you. 

No virus found in this incoming message.
Checked by AVG.
Version: 7.5.524 / Virus Database: 269.23.9/1418 - Release Date: 5/6/2008 5:17 PM

No virus found in this outgoing message.
Checked by AVG. 
Version: 7.5.524 / Virus Database: 269.23.9/1418 - Release Date: 5/6/2008 5:17 PM

-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20080513/441a5666/attachment-0001.html 