[cisco-voip] 911 calls routing out a POTS line via FXO port

[Scott Voll]

is that what the physical locations is for?

I was going to look into the difference between locations and physical
locations.

Scott

On Tue, May 13, 2008 at 8:25 AM, Andrew Short <Andrew.Short at cdw.com> wrote:

>  CER/E911 is decent, and does a few things nothing else will do (central
> site screen pops for 911 calls, callback to non-DIDs, ERLs per switchport,
> etc) but I've found UC6 and device mobility to be excellent at routing calls
> to 911 based on location of the phone.    If you have UC6 already, you
> should investigate device mobility.
>
>
>
> **Please note my new email address:  andrew.short at cdw.com
>
> --
>
> Andrew Short, CCIE #6641
>
> CDW Berbee
>
> 11711 North Meridian Street, Suite 225
>
> Carmel, Indiana  46032
>
> 317.569.4222 - office
>
> 317.569.4201 - fax
>
> andrew.short at cdw.com
>
> www.berbee.com
>
>
>
> *From:* cisco-voip-bounces at puck.nether.net [mailto:
> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Scott Voll
> *Sent:* Tuesday, May 13, 2008 11:21 AM
> *To:* Michael Muscat
> *Cc:* cisco-voip at puck.nether.net
> *Subject:* Re: [cisco-voip] 911 calls routing out a POTS line via FXO port
>
>
>
> each building will need its own CSS.  each building will also need a
> separte 911 partition.  with a route pattern to 911 that points to the local
> VGW.
>
>
>
> The negitive with this is that if anyone moves between buildings and the
> CSS doesn't change.... you still have the same general issue.  (911 goes out
> the wrong VGW).
>
>
>
> Better solution is either Cisco Emergency Responder or third party E911
> solution.  This makes the phone --> 911 dynamic and can go out your defualt
> VGW (PRI) and end up at the PSAP correctly with the right Building location.
>
>
>
> Hope that all makes sense.
>
>
>
> Scott
>
> On Tue, May 13, 2008 at 7:58 AM, Michael Muscat <michaelm at umcu.org> wrote:
>
> Hello all,
>
> I have 7 buildings and need all calls to 911 to go out a different POTS
> line through the router in each building.  Currently if 911 is dialed it
> goes out our outbound PRI and all calls are showing as originating from
> our Data Center so the police go there instead of where the call is
> actually coming from.  If anyone can help me with either the command to
> input into the router at each location to make 911 calls go out an FXO
> or FXS port, or something to setup on CM 4.1.3 itself, I would really
> appreciate it.  Or if there are any other ways of setting this up.
>
> Thanks a lot,
>
> Michael Muscat
> University of Michigan Credit Union
> michaelm at umcu.org
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20080513/b8b8eb55/attachment.html