[cisco-voip] PRI Issue

[Steven Sarte]

Thanks everyone for the input.  In the end all that was needed was a
power down of the smartjack.

Thanks again,
Steven Sarte

On Tue, Nov 18, 2008 at 1:59 PM, Turpin, Mark <mark.turpin at calence.com> wrote:
> It doesn't look like you've got the physical interface up.  Might want to start with the wiring.
>
>
> --
>
> MARK TURPIN  |  Systems Engineer  |  CCIE 21649 |  Calence / Insight Networking Solutions  | www.calence.com
> t. 314.656.2315   c. 314.660.5800   f. 314.656.2355   mark.turpin at calence.com
>
> The information contained in this message and any attachment may contain privileged or confidential information protected from disclosure. If you are not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any review, dissemination, distribution or copying of this information is strictly prohibited.  If you have received this transmission in error, please notify the sender immediately by replying to this message and destroying the original and all copies.  Thank you.
>
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Steven Sarte
> Sent: Tuesday, November 18, 2008 12:54 PM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] PRI Issue
>
> I'm bringing up a PRI circuit remotely and having issues bringing it
> up.  I called the Telco and they said they have no issues on my end.
> They claim it is a signaling issue, they are getting this error "Out
> of service block.  No response. Auto"  .
>
> I did research on Receiver is getting AIS which says that the issue is
> on the Telco side.   But they say they have no issues on their end.
>
> T1 0/0/0 is down.
>  Applique type is Channelized T1
>  Cablelength is long 0db
>  Transmitter is sending remote alarm.
>  Receiver is getting AIS.
>  alarm-trigger is not set
>  Soaking time: 3, Clearance time: 10
>  AIS State:Clear  LOS State:Clear  LOF State:Clear
>  Version info Firmware: 20071011, FPGA: 13, spm_count = 0
>  Framing is ESF, Line Code is B8ZS, Clock Source is Line.
>  CRC Threshold is 320. Reported from firmware  is 320.
>  Data in current interval (126 seconds elapsed):
>     0 Line Code Violations, 0 Path Code Violations
>     1 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
>     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 125 Unavail Secs
>
> USSTFVG01#show isdn status
> Global ISDN Switchtype = primary-ni
> ISDN Serial0/0/0:23 interface
>        dsl 0, interface ISDN Switchtype = primary-ni
>    Layer 1 Status:
>        DEACTIVATED
>    Layer 2 Status:
>        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
>    Layer 3 Status:
>        0 Active Layer 3 Call(s)
>    Active dsl 0 CCBs = 0
>    The Free Channel Mask:  0x00000000
>    Number of L2 Discards = 0, L2 Session ID = 1
>    Total Allocated ISDN CCBs = 0
>
>
> Thanks,
> Steven Sarte
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>