[cisco-voip] Hotline question

[Lelio Fulgenzi]

I think it's an SCCP only config. 

--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Bad grammar makes me [sic]" - Tshirt 


----- Original Message ----- 
From: "Tim Reimers" <treimers at ashevillenc.gov> 
To: "Lelio Fulgenzi" <lelio at uoguelph.ca>, "Terry Oakley" <Terry.Oakley at rdc.ab.ca> 
Cc: cisco-voip at puck.nether.net 
Sent: Monday, February 16, 2009 3:24:55 PM GMT -05:00 US/Canada Eastern 
Subject: RE: [cisco-voip] Hotline question 


Does that alternative work under MGCP or only H.323? 


Tim Reimers 
Systems Analyst II 
Information Technology Services 
City of Asheville 
70 Court Plaza 
Asheville, NC 28801 
phone - 828-259-5512 
treimers at ashevillenc.gov 



From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi 
Sent: Sunday, February 15, 2009 9:32 PM 
To: Terry Oakley 
Cc: cisco-voip at puck.nether.net 
Subject: Re: [cisco-voip] Hotline question 



Hot lines are done the same way on analog sets as you do ip sets. 


    1. create a partition: HotLine_ToShipping_PT 
    2. create a blank translation to the target DN, please it in HotLine_ToShipping_PT 
    3. create a calling search space, HotLine_ToShipping_CSS 
    4. assign the above CSS to the device. 

Alternatively (and I haven't tested this yet) you can create a PLAR type config on the VG224 CLI. This should enable ringdowns to work during SRST. 

--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
"Bad grammar makes me [sic]" - Tshirt 


----- Original Message ----- 
From: "Terry Oakley" <Terry.Oakley at rdc.ab.ca> 
To: cisco-voip at puck.nether.net 
Sent: Sunday, February 15, 2009 9:26:06 PM GMT -05:00 US/Canada Eastern 
Subject: [cisco-voip] Hotline question 

Does anyone know how (CUCM 6.1) to setup a Hotline on an analog set connected via a VGC? I saw the PLAR for the 7941/7961 sets but we have a set by our Shipping and Receiving department that is an old analog (no dial on it) that is used for after hours deliveries. On our old Nortel system we could do it. Just wondering if there is a way to do it on our Cisco system. Thanks in advance Terry Terry Oakley Telecommunication Coordinator, Information Technology Services 100 College Blvd, Red Deer, AB T4N 5H5 Red Deer College Tel (403) 342-3521 Terry.Oakley at rdc.ab.ca When you get here you understand 
_______________________________________________ cisco-voip mailing list cisco-voip at puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20090216/e4fee02e/attachment.html>