[cisco-voip] Hotline question

[Peter Slow]

I think this should work on an analog MGCP endpoint as well. H.323 IOS
endpoints require a dirrent type of PLAR config.

-Pete

On Mon, Feb 16, 2009 at 3:27 PM, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
> I think it's an SCCP only config.
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>
> ----- Original Message -----
> From: "Tim Reimers" <treimers at ashevillenc.gov>
> To: "Lelio Fulgenzi" <lelio at uoguelph.ca>, "Terry Oakley"
> <Terry.Oakley at rdc.ab.ca>
> Cc: cisco-voip at puck.nether.net
> Sent: Monday, February 16, 2009 3:24:55 PM GMT -05:00 US/Canada Eastern
> Subject: RE: [cisco-voip] Hotline question
>
> Does that alternative work under MGCP or only H.323?
>
>
> Tim Reimers
> Systems Analyst II
> Information Technology Services
> City of Asheville
> 70 Court Plaza
> Asheville, NC 28801
> phone - 828-259-5512
> treimers at ashevillenc.gov
>
> ________________________________
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi
> Sent: Sunday, February 15, 2009 9:32 PM
> To: Terry Oakley
> Cc: cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] Hotline question
>
> Hot lines are done the same way on analog sets as you do ip sets.
>
> create a partition: HotLine_ToShipping_PT
> create a blank translation to the target DN, please it in
> HotLine_ToShipping_PT
> create a calling search space, HotLine_ToShipping_CSS
> assign the above CSS to the device.
>
> Alternatively (and I haven't tested this yet) you can create a PLAR type
> config on the VG224 CLI. This should enable ringdowns to work during SRST.
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>
> ----- Original Message -----
> From: "Terry Oakley" <Terry.Oakley at rdc.ab.ca>
> To: cisco-voip at puck.nether.net
> Sent: Sunday, February 15, 2009 9:26:06 PM GMT -05:00 US/Canada Eastern
> Subject: [cisco-voip] Hotline question
>
> Does anyone know how (CUCM 6.1) to setup a Hotline on an analog set
> connected via a VGC? I saw the PLAR for the 7941/7961 sets but we have a set
> by our Shipping and Receiving department that is an old analog (no dial on
> it) that is used for after hours deliveries. On our old Nortel system we
> could do it. Just wondering if there is a way to do it on our Cisco system.
> Thanks in advance Terry Terry Oakley Telecommunication Coordinator,
> Information Technology Services 100 College Blvd, Red Deer, AB T4N 5H5 Red
> Deer College Tel (403) 342-3521 Terry.Oakley at rdc.ab.ca When you get here you
> understand
> _______________________________________________ cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>