[cisco-voip] CUPC without AD?

[Voice Noob]

Also the new version of CUPS supports a diffrent LDAP server then just AD.
Some open ldap or something like that. YOu can problably find it in the
release notes. you still need an LDAP server it just supports more than AD.
I would be you anything that there is some type of LDAP server that you do
not have access to in the CCIE Voice lab.

On Tue, Jul 21, 2009 at 3:49 PM, Jonathan Charles <jonvoip at gmail.com> wrote:

> I think I need to find a guide for integrating CUPS with CUCM without
> AD or DNS... if there is such a thing...
>
> On Tue, Jul 21, 2009 at 3:48 PM, Jonathan Charles<jonvoip at gmail.com>
> wrote:
> > No Presence Information After Login
> > Solution
> >
> > Complete these steps:
> >
> >   1.
> >
> >      Ensure that the DNS server the PC is pointed to can resolve the
> > fully qualified name of the CUPS server.
> >
> >      The host entry will not suffice, you must resolve via DNS.
> >   2.
> >
> >      Check the SUBSCRIBE CSS on the SIP trunk to CUP.
> >
> >      This CSS must include the partitions of the devices you are
> > trying to receive status on.
> >   3.
> >
> >      The CUP SIP proxy incoming access control list (ACL) is not
> > allowing incoming SIP presence messages to reach the presence engine.
> > As a test, set the incoming ACL to ALL and reset the SIP proxy and
> > presence engine. Then, re-login to the CUPC. After this, you can try
> > to reconfigure the incoming ACL properly.
> >
> >
> > Interestingly, there is no DNS on the lab either...
> >
> >
> > Jonathan
> >
> > On Tue, Jul 21, 2009 at 3:42 PM, Ryan Ratliff<rratliff at cisco.com> wrote:
> >> Check the troubleshooting guide for CUPC.  You have to get presence
> before
> >> you can IM.
> >>
> >> -Ryan
> >>
> >> On Jul 21, 2009, at 4:32 PM, Jonathan Charles wrote:
> >>
> >> Well, I can get CUPC to control phones, I can login with CUCM
> >> credentials...  but no IM, and no presence stuff...
> >>
> >> J
> >>
> >> On Tue, Jul 21, 2009 at 3:22 PM, Ryan Ratliff<rratliff at cisco.com>
> wrote:
> >>>
> >>> It may not.  The 7.0 deployment guide actually mentions that you can
> >>> integrate CUCM with AD and not CUPS but it is not recommended as it
> >>> basically neuters CUPC and causes performance issues.  It also notes
> that
> >>> if
> >>> CUCM ldap authentication is enabled CUPC will use CUCM for
> authentication
> >>> (because CUPS syncs the enduser table from CUCM) so maybe it will work,
> >>> but
> >>> not well.
> >>>
> >>> -Ryan
> >>>
> >>> On Jul 21, 2009, at 4:16 PM, Jonathan Charles wrote:
> >>>
> >>> Wait, the CCIE V lab uses CUPS and CUPC but does not have AD... so no
> >>> LDAP... how does CUPC work then?
> >>>
> >>>
> >>>
> >>> J
> >>>
> >>> On Tue, Jul 21, 2009 at 3:14 PM, Ryan Ratliff<rratliff at cisco.com>
> wrote:
> >>>>
> >>>> Welcome to CUPS :)
> >>>>
> >>>> As I said CUCM is no longer an ldap server so you will need to build
> an
> >>>> ldap
> >>>> to point CUPS to.  If you don't want to do ldap sync on CUCM then the
> >>>> userids must be the same in ldap server CUPS is using and in CUCM.
>  You
> >>>> also
> >>>> cannot add contacts via CUPC when CUCM is not enabled for ldap sync
> (you
> >>>> have to use the CUPS User pages).
> >>>>
> >>>> -Ryan
> >>>>
> >>>> On Jul 21, 2009, at 4:10 PM, Jonathan Charles wrote:
> >>>>
> >>>> Well, I have CUCM 7 and CUPS 7 and I want to be able to query CUCM for
> >>>> users from CUPC (so I can add users, etc...)
> >>>>
> >>>> CUCM is NOT AD integrated, and I want to set up CUPS to  point at
> CUCM...
> >>>>
> >>>>
> >>>> Jonathan
> >>>>
> >>>> On Tue, Jul 21, 2009 at 3:04 PM, Ryan Ratliff<rratliff at cisco.com>
> wrote:
> >>>>>
> >>>>> Since CUPS is not supported with any Windows-based CUCM I seriously
> >>>>> doubt
> >>>>> it
> >>>>> was ever tested using DCD as the ldap source.
> >>>>>
> >>>>> CUPS does _require_ ldap.  The ldap source can be anything that CUCM
> >>>>> supports (AD, ND, etc).  Any CUCM that supports CUPS is not an ldap
> >>>>> server.
> >>>>>
> >>>>> -Ryan
> >>>>>
> >>>>> On Jul 21, 2009, at 3:43 PM, Jonathan Charles wrote:
> >>>>>
> >>>>> How do you configure it?
> >>>>>
> >>>>> Do you set up LDAP to point to CUCM?
> >>>>>
> >>>>> Cuz I cannot search for users in DC Directory (CUCM) for CUPC.... am
> I
> >>>>> missing something?
> >>>>>
> >>>>>
> >>>>> J
> >>>>> _______________________________________________
> >>>>> cisco-voip mailing list
> >>>>> cisco-voip at puck.nether.net
> >>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
> >>>>>
> >>>>>
> >>>>
> >>>>
> >>>
> >>>
> >>
> >>
> >
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20090721/ad67926b/attachment.html>