[cisco-voip] Help with first time VOIP setup.

[Anthony R. Mattke]

Without using sccp for my fxs, is there another way to accomplish my goal?

Basicly I'm going to have 2 lines coming in on FXO ports. One of them is 
the home line, one is my office line. I would like to be able to answer 
either of them on my 7960. But also ring the FXS port when calls come in 
  on the home line.

Thanks again for all the help..

-T

Paul wrote:
> Doh. You can't use SCCP to control your FXS port then...an ATA in this case would come in handy to use a device connected to its FXS port but that isn't the point in this case. . . 
> 
> 
> ----- Original Message ----
> From: Anthony R. Mattke <a.mattke at gmail.com>
> To: Paul <asobihoudai at yahoo.com>
> Cc: cisco-voip at puck.nether.net
> Sent: Wednesday, June 17, 2009 12:35:24 AM
> Subject: Re: [cisco-voip] Help with first time VOIP setup.
> 
> I just found this as well..
> 
> http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxsfeatmd.html#wp1108210
> 
> So, this is maybe not supported on the 1760 ???
> 
> Is there another method I could use to ring the FXS port at the same time as the ephone-dn ???
> 
> -Tony
>> Anthony R. Mattke wrote:
>>> Well, I found the service on this page.
>>> http://uc500.com/using-stcapp-make-fxs-port-sccp-phone
>>>
>>> which takes you to this page on Cisco's website.
>>>
>>> http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html 
>>>
>>> There I see
>>> Prerequisites for SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways
>>>
>>> Cisco IOS Gateway
>>>
>>> •Cisco IOS Release 12.3(11)T or a later release.
>>> --- I'm running 12.4(15)T7 Voice9-M
>>>
>>> •The Cisco voice gateway is set up and configured for operation. For information, see the appropriate Cisco configuration documentation.
>>>
>>>
>>> •The analog FXS voice ports are set up and configured for operation. For information, see the Cisco IOS Voice Port Configuration Guide.
>>>
>>>
>>> •SCCP and the SCCP telephony control (STC) application is enabled on the Cisco voice gateway. For configuration information, see "Configuring FXS Ports for Basic Calls" on page 25.
>>>
>>>
>>> Tne rest of these seem fine, yet I have no STCAPP
>>>
>>> -Tony
>>>
>>> Paul wrote:
>>>> I could be wrong, but I'm pretty sure the document referencing this ability states the version of IOS and possibly rooter required.
>>>>
>>>>
>>>> ----- Original Message ----
>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>> To: Paul <asobihoudai at yahoo.com>
>>>> Cc: cisco-voip at puck.nether.net
>>>> Sent: Tuesday, June 16, 2009 10:40:02 PM
>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>
>>>> Yeah, I think I found what I"m looking for.. but I need to do some more research, as my IOS or router isn't supporting what I found..
>>>>
>>>> It shows setting up something such as the following.
>>>>
>>>> !
>>>> dial-peer voice 55 pots
>>>> service stcapp
>>>> port 1/1
>>>> !
>>>> voice-port 1/1
>>>> caller-id enable
>>>> !
>>>> ephone 10
>>>> device-security-mode none
>>>> mac-address DA2F.E2B0.0001
>>>> type anl
>>>> button 1:5
>>>> !
>>>>
>>>>
>>>> I stcapp isn't shown on the service options list, but it lets me enter it. Altho when I try ot get the mac address from show stcapp device summary -- that command is missing..
>>>>
>>>> Can't seem to find much on the Cisco FN on this topic.. is this a device limitation, or is it IOS based?
>>>>
>>>> -Tony
>>>>
>>>>
>>>> Paul wrote:
>>>>> search for fxs sccp controlled or something like that...
>>>>>
>>>>>
>>>>> ----- Original Message ----
>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>> Cc: cisco-voip at puck.nether.net
>>>>> Sent: Tuesday, June 16, 2009 10:19:29 PM
>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>
>>>>> I had no clue you could do that.. Sorry ! I'll look and see if I find an example of that done.
>>>>>
>>>>> Thanks !
>>>>>
>>>>> -Tony
>>>>>
>>>>>
>>>>> Paul wrote:
>>>>>> Then make it an ephone by registering your FXS port using SCCP.
>>>>>>
>>>>>> It's easier that way...
>>>>>>
>>>>>>
>>>>>> ----- Original Message ----
>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>>> Cc: cisco-voip at puck.nether.net
>>>>>> Sent: Tuesday, June 16, 2009 10:12:37 PM
>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>>
>>>>>> One of them isn't an ephone. Its a FXS port using a dial-peer such as..
>>>>>>
>>>>>> !
>>>>>> dial-peer voice 55 pots
>>>>>> destination-pattern 55
>>>>>> port 1/1
>>>>>> !
>>>>>>
>>>>>> And then a ephone-dn that I want to use the same extension, or make ring at the same time so either can answer the call..
>>>>>>
>>>>>> Paul wrote:
>>>>>>> Use overlay.
>>>>>>>
>>>>>>> Assign ephone one and two the same extension originating from two separate ephone-DNs and then use overlay to have them both ring.
>>>>>>>
>>>>>>>
>>>>>>> ----- Original Message ----
>>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>>> To: cisco-voip at puck.nether.net
>>>>>>> Sent: Tuesday, June 16, 2009 6:13:32 PM
>>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>>>
>>>>>>> Ok, so today, I've been attempting to have two phones ring for the same extension.
>>>>>>>
>>>>>>> I see this is fairly simple if they're both ephones, but what about 1 ephone and 1 pots ? I can't seem to make this work, and I can't find any documentation regarding setting this up.
>>>>>>>
>>>>>>> -Tony
>>>>>>> _______________________________________________
>>>>>>> cisco-voip mailing list
>>>>>>> cisco-voip at puck.nether.net
>>>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>      
>>>>>>    
>>>>>    
>>>>
>>>>      
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
> 
> 
>       
>