[cisco-voip] Help with first time VOIP setup.

[Paul]

Doh. You can't use SCCP to control your FXS port then...an ATA in this case would come in handy to use a device connected to its FXS port but that isn't the point in this case. . . 


----- Original Message ----
From: Anthony R. Mattke <a.mattke at gmail.com>
To: Paul <asobihoudai at yahoo.com>
Cc: cisco-voip at puck.nether.net
Sent: Wednesday, June 17, 2009 12:35:24 AM
Subject: Re: [cisco-voip] Help with first time VOIP setup.

I just found this as well..

http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxsfeatmd.html#wp1108210

So, this is maybe not supported on the 1760 ???

Is there another method I could use to ring the FXS port at the same time as the ephone-dn ???

-Tony
> 
> Anthony R. Mattke wrote:
>> Well, I found the service on this page.
>> http://uc500.com/using-stcapp-make-fxs-port-sccp-phone
>> 
>> which takes you to this page on Cisco's website.
>> 
>> http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html 
>> 
>> There I see
>> Prerequisites for SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways
>> 
>> Cisco IOS Gateway
>> 
>> •Cisco IOS Release 12.3(11)T or a later release.
>> --- I'm running 12.4(15)T7 Voice9-M
>> 
>> •The Cisco voice gateway is set up and configured for operation. For information, see the appropriate Cisco configuration documentation.
>> 
>> 
>> •The analog FXS voice ports are set up and configured for operation. For information, see the Cisco IOS Voice Port Configuration Guide.
>> 
>> 
>> •SCCP and the SCCP telephony control (STC) application is enabled on the Cisco voice gateway. For configuration information, see "Configuring FXS Ports for Basic Calls" on page 25.
>> 
>> 
>> Tne rest of these seem fine, yet I have no STCAPP
>> 
>> -Tony
>> 
>> Paul wrote:
>>> I could be wrong, but I'm pretty sure the document referencing this ability states the version of IOS and possibly rooter required.
>>> 
>>> 
>>> ----- Original Message ----
>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>> To: Paul <asobihoudai at yahoo.com>
>>> Cc: cisco-voip at puck.nether.net
>>> Sent: Tuesday, June 16, 2009 10:40:02 PM
>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>> 
>>> Yeah, I think I found what I"m looking for.. but I need to do some more research, as my IOS or router isn't supporting what I found..
>>> 
>>> It shows setting up something such as the following.
>>> 
>>> !
>>> dial-peer voice 55 pots
>>> service stcapp
>>> port 1/1
>>> !
>>> voice-port 1/1
>>> caller-id enable
>>> !
>>> ephone 10
>>> device-security-mode none
>>> mac-address DA2F.E2B0.0001
>>> type anl
>>> button 1:5
>>> !
>>> 
>>> 
>>> I stcapp isn't shown on the service options list, but it lets me enter it. Altho when I try ot get the mac address from show stcapp device summary -- that command is missing..
>>> 
>>> Can't seem to find much on the Cisco FN on this topic.. is this a device limitation, or is it IOS based?
>>> 
>>> -Tony
>>> 
>>> 
>>> Paul wrote:
>>>> search for fxs sccp controlled or something like that...
>>>> 
>>>> 
>>>> ----- Original Message ----
>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>> To: Paul <asobihoudai at yahoo.com>
>>>> Cc: cisco-voip at puck.nether.net
>>>> Sent: Tuesday, June 16, 2009 10:19:29 PM
>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>> 
>>>> I had no clue you could do that.. Sorry ! I'll look and see if I find an example of that done.
>>>> 
>>>> Thanks !
>>>> 
>>>> -Tony
>>>> 
>>>> 
>>>> Paul wrote:
>>>>> Then make it an ephone by registering your FXS port using SCCP.
>>>>> 
>>>>> It's easier that way...
>>>>> 
>>>>> 
>>>>> ----- Original Message ----
>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>> Cc: cisco-voip at puck.nether.net
>>>>> Sent: Tuesday, June 16, 2009 10:12:37 PM
>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>> 
>>>>> One of them isn't an ephone. Its a FXS port using a dial-peer such as..
>>>>> 
>>>>> !
>>>>> dial-peer voice 55 pots
>>>>> destination-pattern 55
>>>>> port 1/1
>>>>> !
>>>>> 
>>>>> And then a ephone-dn that I want to use the same extension, or make ring at the same time so either can answer the call..
>>>>> 
>>>>> Paul wrote:
>>>>>> Use overlay.
>>>>>> 
>>>>>> Assign ephone one and two the same extension originating from two separate ephone-DNs and then use overlay to have them both ring.
>>>>>> 
>>>>>> 
>>>>>> ----- Original Message ----
>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>> To: cisco-voip at puck.nether.net
>>>>>> Sent: Tuesday, June 16, 2009 6:13:32 PM
>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>> 
>>>>>> Ok, so today, I've been attempting to have two phones ring for the same extension.
>>>>>> 
>>>>>> I see this is fairly simple if they're both ephones, but what about 1 ephone and 1 pots ? I can't seem to make this work, and I can't find any documentation regarding setting this up.
>>>>>> 
>>>>>> -Tony
>>>>>> _______________________________________________
>>>>>> cisco-voip mailing list
>>>>>> cisco-voip at puck.nether.net
>>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>>> 
>>>>>> 
>>>>>> 
>>>>>>      
>>>>>    
>>>> 
>>>>    
>>> 
>>> 
>>>      
>> 
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
> 
>