[cisco-voip] Help with first time VOIP setup.

[Anthony R. Mattke]

I just found this as well..

http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxsfeatmd.html#wp1108210

So, this is maybe not supported on the 1760 ???

Is there another method I could use to ring the FXS port at the same 
time as the ephone-dn ???

-Tony
> 
> Anthony R. Mattke wrote:
>> Well, I found the service on this page.
>> http://uc500.com/using-stcapp-make-fxs-port-sccp-phone
>>
>> which takes you to this page on Cisco's website.
>>
>> http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html 
>>
>>
>> There I see
>> Prerequisites for SCCP Controlled Analog (FXS) Ports with 
>> Supplementary Features in Cisco IOS Gateways
>>
>> Cisco IOS Gateway
>>
>> •Cisco IOS Release 12.3(11)T or a later release.
>> --- I'm running 12.4(15)T7 Voice9-M
>>
>> •The Cisco voice gateway is set up and configured for operation. For 
>> information, see the appropriate Cisco configuration documentation.
>>
>>
>> •The analog FXS voice ports are set up and configured for operation. 
>> For information, see the Cisco IOS Voice Port Configuration Guide.
>>
>>
>> •SCCP and the SCCP telephony control (STC) application is enabled on 
>> the Cisco voice gateway. For configuration information, see 
>> "Configuring FXS Ports for Basic Calls" on page 25.
>>
>>
>> Tne rest of these seem fine, yet I have no STCAPP
>>
>> -Tony
>>
>> Paul wrote:
>>> I could be wrong, but I'm pretty sure the document referencing this 
>>> ability states the version of IOS and possibly rooter required.
>>>
>>>
>>> ----- Original Message ----
>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>> To: Paul <asobihoudai at yahoo.com>
>>> Cc: cisco-voip at puck.nether.net
>>> Sent: Tuesday, June 16, 2009 10:40:02 PM
>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>
>>> Yeah, I think I found what I"m looking for.. but I need to do some 
>>> more research, as my IOS or router isn't supporting what I found..
>>>
>>> It shows setting up something such as the following.
>>>
>>> !
>>> dial-peer voice 55 pots
>>> service stcapp
>>> port 1/1
>>> !
>>> voice-port 1/1
>>> caller-id enable
>>> !
>>> ephone 10
>>> device-security-mode none
>>> mac-address DA2F.E2B0.0001
>>> type anl
>>> button 1:5
>>> !
>>>
>>>
>>> I stcapp isn't shown on the service options list, but it lets me 
>>> enter it. Altho when I try ot get the mac address from show stcapp 
>>> device summary -- that command is missing..
>>>
>>> Can't seem to find much on the Cisco FN on this topic.. is this a 
>>> device limitation, or is it IOS based?
>>>
>>> -Tony
>>>
>>>
>>> Paul wrote:
>>>> search for fxs sccp controlled or something like that...
>>>>
>>>>
>>>> ----- Original Message ----
>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>> To: Paul <asobihoudai at yahoo.com>
>>>> Cc: cisco-voip at puck.nether.net
>>>> Sent: Tuesday, June 16, 2009 10:19:29 PM
>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>
>>>> I had no clue you could do that. Sorry ! I'll look and see if I find 
>>>> an example of that done.
>>>>
>>>> Thanks !
>>>>
>>>> -Tony
>>>>
>>>>
>>>> Paul wrote:
>>>>> Then make it an ephone by registering your FXS port using SCCP.
>>>>>
>>>>> It's easier that way...
>>>>>
>>>>>
>>>>> ----- Original Message ----
>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>> To: Paul <asobihoudai at yahoo.com>
>>>>> Cc: cisco-voip at puck.nether.net
>>>>> Sent: Tuesday, June 16, 2009 10:12:37 PM
>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>
>>>>> One of them isn't an ephone. Its a FXS port using a dial-peer such 
>>>>> as..
>>>>>
>>>>> !
>>>>> dial-peer voice 55 pots
>>>>> destination-pattern 55
>>>>> port 1/1
>>>>> !
>>>>>
>>>>> And then a ephone-dn that I want to use the same extension, or make 
>>>>> ring at the same time so either can answer the call..
>>>>>
>>>>> Paul wrote:
>>>>>> Use overlay.
>>>>>>
>>>>>> Assign ephone one and two the same extension originating from two 
>>>>>> separate ephone-DNs and then use overlay to have them both ring.
>>>>>>
>>>>>>
>>>>>> ----- Original Message ----
>>>>>> From: Anthony R. Mattke <a.mattke at gmail.com>
>>>>>> To: cisco-voip at puck.nether.net
>>>>>> Sent: Tuesday, June 16, 2009 6:13:32 PM
>>>>>> Subject: Re: [cisco-voip] Help with first time VOIP setup.
>>>>>>
>>>>>> Ok, so today, I've been attempting to have two phones ring for the 
>>>>>> same extension.
>>>>>>
>>>>>> I see this is fairly simple if they're both ephones, but what 
>>>>>> about 1 ephone and 1 pots ? I can't seem to make this work, and I 
>>>>>> can't find any documentation regarding setting this up.
>>>>>>
>>>>>> -Tony
>>>>>> _______________________________________________
>>>>>> cisco-voip mailing list
>>>>>> cisco-voip at puck.nether.net
>>>>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>>>
>>>>>>
>>>>>>
>>>>>>      
>>>>>     
>>>>
>>>>     
>>>
>>>
>>>      
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
> 
>