[cisco-voip] Voice Router - PRI Card Compatibility

[Norton, Mike]

Do "show diag" and look for what is in the PVDM slots. Or, physically open the router and look for what is in the PVDM slots.

--
Mike Norton
I.T. Support
Peace Wapiti School Division No. 76
Helpdesk: 780-831-3080
Direct: 780-831-3076

From: Kim, Hyoun S [mailto:Hyoun.Kim at chartercom.com]
Sent: November-16-09 3:42 PM
To: Norton, Mike; cisco-voip at puck.nether.net
Subject: RE: Voice Router - PRI Card Compatibility

ARG..  I had the feeling it was the wrong card... but wanted to verify with other experts before I raised a hullabaloo.

Thanks Mike.

P.S. - How do I know if a DSP was included in my bundle?

Hyoun Kim
Network Administrator I
Charter Media - East Division
640 Broadmor Blvd, Suite 80
Murfreesboro, TN 37129

Email: Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>
Office: 615.217.6245
Fax: 615.217.6255

From: Norton, Mike [mailto:mikenorton at pwsd76.ab.ca]
Sent: Monday, November 16, 2009 4:41 PM
To: Kim, Hyoun S; cisco-voip at puck.nether.net
Subject: RE: Voice Router - PRI Card Compatibility

HWIC is for data, not voice. As for whether or not they shipped you the wrong card, that depends on what you ordered. ;-)

Don't forget you will need DSP as well, unless the router was purchased as a bundle that came with it.

--
Mike Norton
I.T. Support
Peace Wapiti School Division No. 76
Helpdesk: 780-831-3080
Direct: 780-831-3076


From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Kim, Hyoun S
Sent: November-16-09 3:21 PM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Voice Router - PRI Card Compatibility

I'm not too keen on my VoIP terminology, so please excuse me if you get confused...

My company recently purchased a C2811 router for a VoIP deployment at a branch office. Currently they are using PRI to connect to their analog (Avaya) phone system. I am to remove their analog system entirely and replace it with a Cisco VoIP solution.

While I have never actually installed a Cisco VoIP system from scratch, I have maintained the one at my current office. I have most of the configuration finished on the router, but I cannot specify the voice ports on the new C2811 router. The PRI that is used at the remote office is the same type that is used in my current office.

After a couple hours of troubleshooting, I came to the realization that the card that is currently in use at my office is a "VWIC2-2MFT-T1/E1". The card that came with my voice router for the remote branch is a "HWIC-1DSU-T1". Is this the reason why I cannot configure my voice ports? Did they ship me the wrong card?

Thanks in advance.


[cid:image001.jpg at 01CA66D3.C1E62AE0]
________________________________
Hyoun Kim * Network Administrator I - East Division
640 Broadmor Blvd * Suite 80 * Murfreesboro, TN 37129
' 615.217.6245 * ' 859.312.6941 * 7 615.217.6255 * * Hyoun.Kim at chartercom.com<mailto:Hyoun.Kim at chartercom.com>




E-MAIL CONFIDENTIALITY NOTICE:















The contents of this e-mail message and

any attachments are intended solely for the

addressee(s) and may contain confidential

and/or legally privileged information. If you

are not the intended recipient of this message

or if this message has been addressed to you

in error, please immediately alert the sender

 by reply e-mail and then delete this message

and any attachments. If you are not the

intended recipient, you are notified that

any use, dissemination, distribution, copying,

or storage of this message or any attachment

is strictly prohibited.

















E-MAIL CONFIDENTIALITY NOTICE:















The contents of this e-mail message and

any attachments are intended solely for the

addressee(s) and may contain confidential

and/or legally privileged information. If you

are not the intended recipient of this message

or if this message has been addressed to you

in error, please immediately alert the sender

 by reply e-mail and then delete this message

and any attachments. If you are not the

intended recipient, you are notified that

any use, dissemination, distribution, copying,

or storage of this message or any attachment

is strictly prohibited.














-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20091116/2a34a24e/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 1990 bytes
Desc: image001.jpg
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20091116/2a34a24e/attachment.jpg>