[cisco-voip] Configuring ASYNC NM in 2811

[Mark Holloway]

Found what I needed.

http://www.cisco.com/en/US/products/hw/routers/ps282/products_tech_note09186a008035b051.shtml

AccessServer#show line
   Tty Line Typ     Tx/Rx    A Modem  Roty AccO AccI  Uses  Noise Overruns  Int
      0    0 CTY              -    -      -    -    -     0      0    0/0      -
      1    1 AUX   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/0   66 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/1   67 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/2   68 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/3   69 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/4   70 TTY   9600/9600  -    -      -    -    -     0     20    9/28     -
    1/5   71 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/6   72 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/7   73 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/8   74 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
    1/9   75 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
   1/10   76 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
   1/11   77 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
   1/12   78 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
   1/13   79 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
   1/14   80 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
   1/15   81 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -
*   514  514 VTY              -    -      -    -    -     1      0    0/0      -
    515  515 VTY              -    -      -    -    -     0      0    0/0      -
    516  516 VTY              -    -      -    -    -     0      0    0/0      -
    517  517 VTY              -    -      -    -    -     0      0    0/0      -
    518  518 VTY              -    -      -    -    -     0      0    0/0      -

AccessServer(config)#ip host br2 2069 10.1.1.1
AccessServer(config)#^Z
AccessServer#br2
Translating "br2"

Translating "br2"
Trying br2 (10.1.1.1, 2069)... Open

r3-br2#



On Nov 22, 2009, at 1:34 PM, Mark Holloway wrote:

> I have an ASYNC 16A/S network module in a 2811 and I'm not understanding how to associate the 'line' with the ip host command so I may use the 2811 to manage several console connections to other Cisco routers.  This was simple to configure when using a 3600 slotted with the ASYNC module but on the 2811 the 'line' is different.
> 
> My old 3600 'sh run'
> 
> line 33 81
> session-timeout 5 
> transport input all
> autohangup
> stopbits 1
> 
> interface Loopback0
> ip address 10.1.1.1 255.255.255.255
> 
> ip host br2 2033 10.1.1.1
> 
> AccessServer# br2
> 
> Password:
> 
> 
> 
> Current 2811 'sh run' 
> 
> line 1/0 1/15
> session-timeout 5 
> transport input all
> autohangup
> stopbits 1
> 
> interface Loopback0
> ip address 10.1.1.1 255.255.255.255
> 
> ip host br2 2000 10.1.1.1
> 
> AccessServer# br2
> 
> % Connection refused by remote host
> 
> 
> 
> I believe my port number in the ip host statement is not correct.  Based on 'line 1/0 1/15' I have not idea how to correlate that.  Has anyone successfully configured this before?
> 
> 
> 
> 
> 
>