[cisco-voip] DMA and upgrade at the same time?

[Wes Sisk]

"W1" is import of the windows export, basically importing the DMA output.

/Wes

On Thursday, October 01, 2009 2:30:31 PM, Rasim Duric 
<rduric at uoguelph.ca> wrote:
>
> Hi Wes,
>
>  
>
> What is a W1 Install? Is this like an install from the scratch, from a 
> CD/DVD? Thanks in advance.
>
>  
>
> Rasim Duric
>
> Network Analyst (CCS)
>
> University of Guelph
>
> Guelph, N1G 2W1, ON
>
> 519-824-4120x53146
>
> rduric at uoguelph.ca
>
>  
>
> *From:* cisco-voip-bounces at puck.nether.net 
> [mailto:cisco-voip-bounces at puck.nether.net] *On Behalf Of *Wes Sisk
> *Sent:* September-28-09 2:07 PM
> *To:* Lelio Fulgenzi
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] DMA and upgrade at the same time?
>
>  
>
> Hi Lelio,
>
> Some thunderbird prowess finally provided the answer:
>
> ********************
> You can't do an upgrade during a W1.  You can do an upgrade followed 
> by a W1 only if the DMA tarball was created for the version of 
> software you upgraded to.  If it was not, you will most likely hit a 
> DB failure.  If the software upgraded to is 6.1.2+, the W1 failure 
> most likely would be due to detection of invalid DMA version versus 
> active version.
> ********************
>
> I also confirmed that a few individuals in TAC have observed successes 
> performing upgrade and import.  These were primarily motivated by the 
> availability of bootable media. For example:
>
> 1. use dma 7.1.3 to export your CM4.1.3 data
> 2. boot from your CM7.0.2 bootable media
> 3. select to upgrade during install
> 4. point to cm713 upgrade file on sftp server
> 5. let install proceed, it will trigger another reboot
> 6. after reboot install will start again. at this point select to 
> import windows data and point to dma file on sftp server
>
> Key being that you used dma for 7.1.3 and used CM version 7.1.3 as the 
> final destination version.  This is just a workaround for not having 
> 7.1.3 bootable media.
>
> Regards,
> Wes
>
> On Monday, September 28, 2009 1:05:37 PM, Lelio Fulgenzi 
> <lelio at uoguelph.ca> <mailto:lelio at uoguelph.ca> wrote:
>
> ugh.
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>
> ----- Original Message -----
> From: "Matthew Loraditch" <MLoraditch at heliontechnologies.com> 
> <mailto:MLoraditch at heliontechnologies.com>
> To: "Lelio Fulgenzi" <lelio at uoguelph.ca> <mailto:lelio at uoguelph.ca>, 
> "Wes Sisk" <wsisk at cisco.com> <mailto:wsisk at cisco.com>
> Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net> 
> <mailto:cisco-voip at puck.nether.net>
> Sent: Monday, September 28, 2009 12:55:23 PM GMT -05:00 US/Canada Eastern
> Subject: RE: [cisco-voip] DMA and upgrade at the same time?
>
> DMA Import is at install only so you will have to install and dma and 
> then upgrade after you complete the install
>
>  
>
>  
>
> *Matthew Loraditch*
> 1965 Greenspring Drive
>
> Timonium, MD 21093
> support at heliontechnologies.com <mailto:support at heliontechnologies.com>
> (p) (410) 252-8830
> (F) (443) 541-1593
>
> Visit us at www.heliontechnologies.com 
> <http://www.heliontechnologies.com>
> Support Issue? Email support at heliontechnologies.com 
> <mailto:support at heliontechnologies.com> for fast assistance!
>
>  
>
> *From:* cisco-voip-bounces at puck.nether.net 
> <mailto:cisco-voip-bounces at puck.nether.net> 
> [mailto:cisco-voip-bounces at puck.nether.net] *On Behalf Of *Lelio Fulgenzi
> *Sent:* Monday, September 28, 2009 12:53 PM
> *To:* Wes Sisk
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] DMA and upgrade at the same time?
>
>  
>
> ok. thanks. can i do a DMA import after an installation + upgrade is 
> completed? or does DMA import have to be done at install time?
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>
> ----- Original Message -----
> From: "Wes Sisk" <wsisk at cisco.com> <mailto:wsisk at cisco.com>
> To: "Lelio Fulgenzi" <lelio at uoguelph.ca> <mailto:lelio at uoguelph.ca>
> Cc: "cisco-voip voyp list" <cisco-voip at puck.nether.net> 
> <mailto:cisco-voip at puck.nether.net>
> Sent: Monday, September 28, 2009 12:26:14 PM GMT -05:00 US/Canada Eastern
> Subject: Re: [cisco-voip] DMA and upgrade at the same time?
>
> I believe DMA import + upgrade at same time are unsupported:
> example: dma 4.1, begin install of 7.0, select import windows, and 
> select to apply additional patches (7.1).
>
> I am looking for supporting documentation.
>
> /Wes
>
> On Monday, September 28, 2009 10:03:50 AM, Lelio Fulgenzi 
> <lelio at uoguelph.ca> <mailto:lelio at uoguelph.ca> wrote:
>
> Sorry if I posted this already....
>
> Does anyone know if you can do both a DMA and upgrade at the same time 
> when installing v7.0 ?
>
> I know I can go through the installation steps myself, but I'm hoping 
> someone will share their experience, secrets or guess.
>
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> "Bad grammar makes me [sic]" - Tshirt
>
>  
>  
> ------------------------------------------------------------------------
>
>
>   
>  
>  
>  
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net <mailto:cisco-voip at puck.nether.net>
> https://puck.nether.net/mailman/listinfo/cisco-voip
>   
>
>  
>
>  
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20091001/fc06e52e/attachment.html>