[cisco-voip] DMA and upgrade at the same time?

[Rasim Duric]

Hi Wes,



What is a W1 Install? Is this like an install from the scratch, from a 
CD/DVD? Thanks in advance.



Rasim Duric

Network Analyst (CCS)

University of Guelph

Guelph, N1G 2W1, ON

519-824-4120x53146

rduric at uoguelph.ca



From: cisco-voip-bounces at puck.nether.net 
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Wes Sisk
Sent: September-28-09 2:07 PM
To: Lelio Fulgenzi
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] DMA and upgrade at the same time?



Hi Lelio,

Some thunderbird prowess finally provided the answer:

********************
You can't do an upgrade during a W1.  You can do an upgrade followed by a W1 
only if the DMA tarball was created for the version of software you upgraded 
to.  If it was not, you will most likely hit a DB failure.  If the software 
upgraded to is 6.1.2+, the W1 failure most likely would be due to detection 
of invalid DMA version versus active version.
********************

I also confirmed that a few individuals in TAC have observed successes 
performing upgrade and import.  These were primarily motivated by the 
availability of bootable media. For example:

1. use dma 7.1.3 to export your CM4.1.3 data
2. boot from your CM7.0.2 bootable media
3. select to upgrade during install
4. point to cm713 upgrade file on sftp server
5. let install proceed, it will trigger another reboot
6. after reboot install will start again. at this point select to import 
windows data and point to dma file on sftp server

Key being that you used dma for 7.1.3 and used CM version 7.1.3 as the final 
destination version.  This is just a workaround for not having 7.1.3 
bootable media.

Regards,
Wes

On Monday, September 28, 2009 1:05:37 PM, Lelio Fulgenzi 
<mailto:lelio at uoguelph.ca> <lelio at uoguelph.ca> wrote:



ugh.

---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt


----- Original Message -----
From: "Matthew Loraditch"  <mailto:MLoraditch at heliontechnologies.com> 
<MLoraditch at heliontechnologies.com>
To: "Lelio Fulgenzi"  <mailto:lelio at uoguelph.ca> <lelio at uoguelph.ca>, "Wes 
Sisk"  <mailto:wsisk at cisco.com> <wsisk at cisco.com>
Cc: "cisco-voip voyp list"  <mailto:cisco-voip at puck.nether.net> 
<cisco-voip at puck.nether.net>
Sent: Monday, September 28, 2009 12:55:23 PM GMT -05:00 US/Canada Eastern
Subject: RE: [cisco-voip] DMA and upgrade at the same time?

DMA Import is at install only so you will have to install and dma and then 
upgrade after you complete the install





Matthew Loraditch
1965 Greenspring Drive

Timonium, MD 21093
 <mailto:support at heliontechnologies.com> support at heliontechnologies.com
(p) (410) 252-8830
(F) (443) 541-1593

Visit us at  <http://www.heliontechnologies.com> www.heliontechnologies.com
Support Issue? Email  <mailto:support at heliontechnologies.com> 
support at heliontechnologies.com for fast assistance!



From: cisco-voip-bounces at puck.nether.net 
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi
Sent: Monday, September 28, 2009 12:53 PM
To: Wes Sisk
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] DMA and upgrade at the same time?



ok. thanks. can i do a DMA import after an installation + upgrade is 
completed? or does DMA import have to be done at install time?

---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt


----- Original Message -----
From: "Wes Sisk"  <mailto:wsisk at cisco.com> <wsisk at cisco.com>
To: "Lelio Fulgenzi"  <mailto:lelio at uoguelph.ca> <lelio at uoguelph.ca>
Cc: "cisco-voip voyp list"  <mailto:cisco-voip at puck.nether.net> 
<cisco-voip at puck.nether.net>
Sent: Monday, September 28, 2009 12:26:14 PM GMT -05:00 US/Canada Eastern
Subject: Re: [cisco-voip] DMA and upgrade at the same time?

I believe DMA import + upgrade at same time are unsupported:
example: dma 4.1, begin install of 7.0, select import windows, and select to 
apply additional patches (7.1).

I am looking for supporting documentation.

/Wes

On Monday, September 28, 2009 10:03:50 AM, Lelio Fulgenzi 
<mailto:lelio at uoguelph.ca> <lelio at uoguelph.ca> wrote:

Sorry if I posted this already....

Does anyone know if you can do both a DMA and upgrade at the same time when 
installing v7.0 ?

I know I can go through the installation steps myself, but I'm hoping 
someone will share their experience, secrets or guess.


---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"Bad grammar makes me [sic]" - Tshirt






  _____






_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip






-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20091001/6c86cb4f/attachment.html>