[cisco-voip] Resolved: 7962 Registration Issues with 7.1.2.32014-1 ?

[Jason Aarons (US)]

8.3(2) can not be upgraded to 8-5-2SR1S . they can however be upgraded
to 8-5-2S. Upgrade them first to 8-5-2S and then 8-5-2SR1S.

Reference for 8.5(2)

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/firmware/8_5_2/engl
ish/release/notes/7900_852SR1.html

For all SCCP firmware upgrades from firmware release versions earlier
than 8.3(3) to version 8.5(2)SR1 or greater, you must first upgrade your
firmware to version 8.5(2). Once you have upgraded to version 8.5(2),
you can upgrade your IP Phone to version 8.5(2)SR1 or later.

 

Reference for 8.5(3) (future)

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/firmware/8_5_3/engl
ish/release/notes/7900_853.html

For all SCCP firmware upgrades from firmware release versions earlier
than 8.3(3) to version 8.5(3) or greater, you must first upgrade your
firmware to version 8.5(2). Once you have upgraded to version 8.5(2),
you can upgrade your IP Phone to version 8.5(3) or later

 

 

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jason Aarons
(US)
Sent: Tuesday, October 06, 2009 7:09 PM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] 7962 Registration Issues with 7.1.2.32014-1 ?
Importance: High

 

 

We are  building new out of box 7962's come from factory running 8.3(2)
and are having registration issues with your 7962/7915s. Our production
CallManager is running 7.1.2.32014-1 and the Device Defaults for 7962
are SCCP42.8-5-2SR1S

 

When the 7962's initially boot and go out to load the firmware, it will
immeidately get an "auth fail".  We are using SCCP Non-Secure Mode.  In
some instances, the phone will fail to load the firmware but will still
register however not many of the functions will work.  I've seen one
instance where the phone actually came up with the right configuration
yet, in Call manager it didn't even show registered.  The status was
"unknown".

 

What we did earlier this morning was pointed a test 7962 to another
7.1(2) cluster and let the phone auto-register and pull the correct
load.  Once the phone came back up and auto-registered to the other
cluster then we just reset the phone dhcp settings to enabled so that
the phones would re-register back to the first cluster.  Once we did
this then the phones would be able to register fine to the original
cluster.

 

 Under the phone configuration in the device information box, the
"Active Load ID" will be unknown.  When you see this you will either
have problems with the 7962 coming up properly issues with the Sidecar
if you have a sidecar.

 

________________________________

Disclaimer: This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the designated
addressee(s) named above only. If you are not the intended addressee,
you are hereby notified that you have received this communication in
error and that any use or reproduction of this email or its contents is
strictly prohibited and may be unlawful. If you have received this
communication in error, please notify us immediately by replying to this
message and deleting it from your computer. Thank you. 




-----------------------------------------
Disclaimer:

This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only.  If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful.  If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20091006/07fe75b9/attachment.html>