[cisco-voip] C1861-SRST-F/K9 with HWIC-1T1/E1

[Carter, Bill]

It is the opposite problem. The card is displayed in IOS, but the card
is not physically installed in the router. The HWIC slot has a blank
cover over it.

 

Show run:

controller T1 0/3/0

 cablelength long 0db

 channel-group 0 timeslots 1-24

!

interface Serial0/3/0:0

 no ip address

!

Show version:

...

1 Serial interface

1 Channelized/Clear T1/PRI port

 

Show diag:

       HWIC Slot 3:

        1 port (2 channel) T1/E1 HWIC

        Hardware Revision        : 0.0

        Top Assy. Part Number    : 800-30196-01

        Part Number              : 73-11458-01

        Board Revision           : A0

        Deviation Number         : 0

        Fab Version              : 04

        PCB Serial Number        : FOC133058ZN

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Version Identifier       : V01

        Product (FRU) Number     : HWIC-1T1/E1

        CLEI Code                : COUIANYCAA

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 D4 41 00 00 C0 46 03 20 00 75 F4 01

          0x10: 82 49 2C C2 01 42 41 30 88 00 00 00 00 02 04 C1

          0x20: 8B 46 4F 43 31 33 33 30 35 38 5A 4E 03 00 81 00

          0x30: 00 00 00 04 00 89 56 30 31 20 CB 8F 48 57 49 43

          0x40: 2D 31 54 31 2F 45 31 20 20 20 20 C6 8A 43 4F 55

          0x50: 49 41 4E 59 43 41 41 D9 02 40 C1 FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

 

From: Nate VanMaren [mailto:VanMarenNP at ldschurch.org] 
Sent: Tuesday, September 22, 2009 9:43 AM
To: Carter, Bill; cisco-voip at puck.nether.net
Subject: RE: C1861-SRST-F/K9 with HWIC-1T1/E1

 

I am guessing you're missing the card type command, and that you can't
see the controller interface in the config, but you can see the physical
interface installed.

 

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Carter, Bill
Sent: Tuesday, September 22, 2009 8:11 AM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] C1861-SRST-F/K9 with HWIC-1T1/E1

 

I have a 1861 and purchased the optional HWIC-1T1/E1. I received my box,
the label says the HWIC-1T1/E1 is included.

 

I can't see the physical T1 port.

 

 

Bill Carter

Senior Business Communications Analyst

CCIE 5022

Sentinel Technologies

SNR 217.391.5015

 



NOTICE: This email message is for the sole use of the intended
recipient(s) and may contain confidential and privileged information.
Any unauthorized review, use, disclosure or distribution is prohibited.
If you are not the intended recipient, please contact the sender by
reply email and destroy all copies of the original message.

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20090922/d39e30d7/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/gif
Size: 3982 bytes
Desc: image001.gif
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20090922/d39e30d7/attachment.gif>