[cisco-voip] MGCP GW logs and autocfg endpoint

[Ryan Ratliff]

Pretty sure CM 4.2 doesn't support the sccp auto-config virtual ports.   At least make sure they are on the last CM 4.2(3)ES.  You can disable it by removing the command "ccm-manager sccp".

-Ryan

On Apr 19, 2010, at 10:19 AM, george.hendrix at l-3com.com wrote:

> Hi Ryan,
>  
>   Yes, I have actually seen this on two different 2800 series routers.  One has a SIP trunk to the PSTN (no MGCP on this one) and the other has T1’s configured under MGCP in CCM.  Also, I am running CCM 4.2.  I was not able to run the command below.  Here is some output from the second router (w/ SIP trunk and no MGCP).  The 3 profiles I have created on both routers are all registered.  Both routers are configured in failover mode in the event connection to CCM is lost.
>  
> AutoCfg_Virtual_Endpoint Oper State: ACTIVE_IN_PROGRESS - Cause Code: TCP_CONN_ERROR
> Active Call Manager: NONE
> TCP Link Status: NOT_CONNECTED, Device Name: AN2497C55638FFF
> Security
>  Signaling Security: AUTHENTICATED TLS
> Reported Max Streams: 0, Reported Max OOS Streams: 0
> Supported Codec: g711ulaw, Maximum Packetization Period: 20
>  
>  
>  
> Bill Hendrix
> <image001.jpg>
> george.hendrix at l-3com.com
> W: 813-281-3109  C: 813-205-0979
> STRATIS Service Desk: 1-800-871-9983
>  
> From: Ryan Ratliff [mailto:rratliff at cisco.com] 
> Sent: Monday, April 19, 2010 9:29 AM
> To: Hendrix, George (Bill) @ STRATIS
> Cc: cisco-voip at puck.nether.net
> Subject: Re: [cisco-voip] MGCP GW logs and autocfg endpoint
>  
> From your CUCM publisher's CLI run this command and provide the output:
> run sql select pkid,name,tkmodel from device where name = 'AN168DD75E80FFF'
>  
> Are you sure this is an MGCP gateway?  The virtual endpoint is typically seen with vg224 sccp devices when the sccp auto-config is enabled.
>  
> -Ryan
>  
> On Apr 17, 2010, at 9:44 AM, george.hendrix at l-3com.com wrote:
> 
> 
> Hi Everyone,
>  
>   I have an MGCP GW setup and have seen a couple of things that do not make sense.
>  
> The first thing is this error.  However, calls go through with no problem, inbound and outbound and all resources are registered with CCM.
>  
> sym_xapp_process_ccapi_events: minor is ZERO - should be non-zero for CCAPI event
>  
> The second thing I see is this auto configured endpoint.
>  
> AutoCfg_Virtual_Endpoint Oper State: ACTIVE_IN_PROGRESS - Cause Code: NOT_REGIS_WITH_CCM
> Active Call Manager: NONE
> TCP Link Status: NOT_CONNECTED, Device Name: AN168DD75E80FFF
> Reported Max Streams: 0, Reported Max OOS Streams: 0
> Supported Codec: g711ulaw, Maximum Packetization Period: 20
>  
> I am not sure what it is and do see any way to remove it.  All profiles that have been created are registered just fine.
>  
> Thanks,
>  
> Bill Hendrix
> L-3 Communications
> george.hendrix at l-3com.com
>  
>  
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>  

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100419/a0305daa/attachment.html>