[cisco-voip] SRST with FXO ports??

[Lelio Fulgenzi]

I don't think so. Not for what you want to do. 

All you need is the "connection plar" config on your port. 



voice-port 0/2/0 
signal groundStart 
echo-cancel coverage 64 
timing hookflash-out 50 
connection plar 37063 


--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
Cooking with unix is easy. You just sed it and forget it. 
- LFJ (with apologies to Mr. Popeil) 


----- Original Message ----- 
From: "Edward Countryman" <Edward.Countryman at provena.org> 
To: "Lelio Fulgenzi" <lelio at uoguelph.ca> 
Cc: "Cisco-Voip-Puck" <cisco-voip at puck.nether.net> 
Sent: Tuesday, April 20, 2010 4:15:06 PM GMT -05:00 US/Canada Eastern 
Subject: RE: [cisco-voip] SRST with FXO ports?? 




Thank you for the doc; Could it be as simple as missing the “DESTINATION-PATTERN XXXX” command??? 





From: Lelio Fulgenzi [mailto:lelio at uoguelph.ca] 
Sent: Tuesday, April 20, 2010 3:07 PM 
To: Countryman, Edward 
Cc: Cisco-Voip-Puck 
Subject: Re: [cisco-voip] SRST with FXO ports?? 




you've got yourself a case of TSD there my friend. (two-stage dialing) 

you need need to configure PLAR on those ports so it goes to your auto-attendant. 

http://www.cisco.com/en/US/tech/tk652/tk698/technologies_tech_note09186a00800e00d0.shtml 

--- 
Lelio Fulgenzi, B.A. 
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1 
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN) 
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 
Cooking with unix is easy. You just sed it and forget it. 
- LFJ (with apologies to Mr. Popeil) 


----- Original Message ----- 
From: "Edward Countryman" <Edward.Countryman at provena.org> 
To: "Cisco-Voip-Puck" <cisco-voip at puck.nether.net> 
Sent: Tuesday, April 20, 2010 3:57:42 PM GMT -05:00 US/Canada Eastern 
Subject: [cisco-voip] SRST with FXO ports?? 




Looking for direction on a config issue, I cant seem to put my finger on the problem 



I have a site with a 2811 (MGCP) with 4-POTS lines connected to a VIC2-4FXO card. 



Outbound calling from the site in SRST mode works just fine, but when I call into one of the POTS lines while in SRST mode the router answers with a dial tone instead of ringing the default internal extension # 1120. What am I missing?? 



dial-peer voice 10 pots 

trunkgroup 1 

answer-address 1120 








_______________________________________________ cisco-voip mailing list cisco-voip at puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100420/c106233b/attachment.html>