[cisco-voip] iLBC Transcoder... FORCE ILBC for some calls???

[Ryan Ratliff]

Very likely you failed to allocate a transcoder OR you tried to do g729 to g729 to an allocated transcoder that doesn't support lbr to lbr.

CCM traces will show you what xcoder is being allocated and where it's failing.

-Ryan

On Apr 22, 2010, at 1:11 PM, Jonathan Charles wrote:

> I tried 723 for the region and got fast busies for calls to the 6608.... 
> 
> On Wed, Apr 21, 2010 at 3:17 PM, Peter Slow <peter.slow at gmail.com> wrote:
> Ryan,
>  I had mentioned to him that configuring the phone to always use a
> TRP and then configuring the TRP to support the approriate codecs
> might do the trick, but havent tried it yet.  the other option was
> setting the region between the 6608 and the phone to 723 to force
> transcoder invocation, but that seemed messy.
> 
> any comments on either solution?
> 
> -Pete
> 
> On Wed, Apr 21, 2010 at 2:15 PM, Ryan Ratliff <rratliff at cisco.com> wrote:
> > In order to force a codec you have to route the call through a device that
> > only supports said codec.  In your case both the 6608 and the phone support
> > g.729 so that is what CUCM is negotiating.   Since you can't disable g.729
> > support on the phone you would need to somehow route the call through and
> > intermediate device that only supports ilbc (for the phone leg) and then
> > engage a transcoder to convert the ilbc to g.711 going to the 6608.
> > Remember the Region setting is just the max bandwidth for calls.  Any codec
> > less than (or equal to) the max and supported by all parties will be
> > allowed.
> > -Ryan
> > On Apr 21, 2010, at 12:56 PM, Jonathan Charles wrote:
> >
> > Basically, the goal is to Force iLBC for all calls from the remote phones...
> > and invoke the transcoder regardless of codec support.
> >
> >
> > Jonathan
> >
> > On Wed, Apr 21, 2010 at 11:22 AM, Jonathan Charles <jonvoip at gmail.com>
> > wrote:
> >>
> >> OK, I have a 6608 and a 7965 remotely over a VPN.
> >>
> >> I have enabled an IOS Enhanced Xcoder... It is never invoked. The region
> >> says G.728/ILBC and it is set to lossy...
> >>
> >> And all calls are going out as G.729...
> >>
> >> The 6608 doesn't support ilbc, but the 65 does... I have enabled the
> >> service parameters:
> >>
> >> iLBC Codec Enabled: Enabled for all devices
> >> Default InterRegion Codec: G.728
> >>
> >> But still 729...
> >>
> >> The quality is horrible using 729... the customer is demanding ilbc (that
> >> is why they bought the 7965s and 62s....) but if the phone will always
> >> default to 729...
> >>
> >>
> >> How???
> >>
> >>
> >>
> >> Jonathan
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
> >
> 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100422/f5c3531f/attachment.html>