[cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card

[Peter Slow]

Since when can't you use a loopback interface is your SCCP bind
interface? I'm not aware of that limitation.

-Peter

On Fri, Apr 23, 2010 at 11:34 AM, Bill <bill at hitechconnection.net> wrote:
> I don’t think you can use a loopback for this. If I remember right this is
> the same as setting up a transcoder / conference bridge resource and you
> have to use a physical adaptor.
>
>
>
> ________________________________
>
> From: Lelio Fulgenzi [mailto:lelio at uoguelph.ca]
> Sent: Friday, April 23, 2010 10:30 AM
> To: Bill
> Cc: cisco-voip voyp list
> Subject: Re: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID
> card
>
>
>
> hmmm, i'm going to be using a loopback address.
>
>
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> Cooking with unix is easy. You just sed it and forget it.
>                               - LFJ (with apologies to Mr. Popeil)
>
>
> ----- Original Message -----
> From: "Bill" <bill at hitechconnection.net>
> To: "Lelio Fulgenzi" <lelio at uoguelph.ca>, "cisco-voip voyp list"
> <cisco-voip at puck.nether.net>
> Sent: Friday, April 23, 2010 11:20:45 AM GMT -05:00 US/Canada Eastern
> Subject: RE: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID
> card
>
> The MAC address you configure for SCCP traffic to bind to.
>
>
>
> sccp local gigabitEthernet 0/0
>
>
>
>
>
>
>
> ________________________________
>
> From: cisco-voip-bounces at puck.nether.net
> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Lelio Fulgenzi
> Sent: Friday, April 23, 2010 10:15 AM
> To: cisco-voip voyp list
> Subject: [cisco-voip] MAC address for SCCP controlled VIC3-2FXS-E/DID card
>
>
>
> OK, silly question, what MAC address do I use when configuring a
> VIC3-2FXS-E/DID with SCCP?
>
> Is it similar to a VG248 where I use the MAC address of fas0/0?
>
> So on a 3900, I would use the MAC address of GigabitEthernet0/0 ?
>
> I'll try that and see how it goes.
>
>
> ---
> Lelio Fulgenzi, B.A.
> Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
> (519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> Cooking with unix is easy. You just sed it and forget it.
>                               - LFJ (with apologies to Mr. Popeil)
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>