[cisco-voip] Internaltional Calls Failing at the Bell PRI

[Go0se]

If it's connecting to Bell, try setting the called type and plan both to
UNKNOWN.

-Go0se

-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of John Lange
Sent: Tuesday, February 02, 2010 2:28 PM
To: Cisco VOIP
Subject: [cisco-voip] Internaltional Calls Failing at the Bell PRI

Ok, now that I've figured out that it's not the dial pattern causing the
problem, I've turned on debugging and this is what I'm getting:

Feb  2 20:20:46.305: ISDN Se0/3/0:23 Q931: Applying typeplan for sw-type
0xD is 0x2 0x1, Calling num 2049757113
Feb  2 20:20:46.305: ISDN Se0/3/0:23 Q931: Applying typeplan for sw-type
0xD is 0x1 0x1, Called num 011448712002000
Feb  2 20:20:46.309: ISDN Se0/3/0:23 Q931: TX -> SETUP pd = 8  callref =
0x30FB 
	Bearer Capability i = 0x8090A2 
		Standard = CCITT 
		Transfer Capability = Speech  
		Transfer Mode = Circuit 
		Transfer Rate = 64 kbit/s 
	Channel ID i = 0xA98390 
		Exclusive, Channel 16 
	Calling Party Number i = 0x2180, '2049757113' 
		Plan:ISDN, Type:National 
	Called Party Number i = 0x91, '011448712002000' 
		Plan:ISDN, Type:International
Feb  2 20:20:46.405: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0xB0FB 
	Cause i = 0x809C - Invalid number format (incomplete number)
-----

I also tried numbering-type international, with the same result:

-----


Feb  2 20:24:43.921: ISDN Se0/3/0:23 Q931: Applying typeplan for sw-type
0xD is 0x2 0x1, Calling num 2049757113
Feb  2 20:24:43.921: ISDN Se0/3/0:23 Q931: Applying typeplan for sw-type
0xD is 0x1 0x1, Called num 011448712002000
Feb  2 20:24:43.921: ISDN Se0/3/0:23 Q931: TX -> SETUP pd = 8  callref =
0x3100 
	Bearer Capability i = 0x8090A2 
		Standard = CCITT 
		Transfer Capability = Speech  
		Transfer Mode = Circuit 
		Transfer Rate = 64 kbit/s 
	Channel ID i = 0xA98390 
		Exclusive, Channel 16 
	Calling Party Number i = 0x2180, '2049757113' 
		Plan:ISDN, Type:National 
	Called Party Number i = 0x91, '011448712002000' 
		Plan:ISDN, Type:International
Feb  2 20:24:44.025: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0xB100 
	Cause i = 0x809C - Invalid number format (incomplete number)

---

I tested this PRI on an Asterisk box and sending 011448712002000 works
so I'm at a loss as to why the Cisco is having problems.

Any suggestions?


-- 
John Lange
http://www.johnlange.ca

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip