[cisco-voip] Internaltional Calls Failing at the Bell PRI

[Cristobal Priego]

With the type international you don't need to send 011 to the pstn

Sent from my iPhone

On Feb 2, 2010, at 12:28 PM, John Lange <john at johnlange.ca> wrote:

> Ok, now that I've figured out that it's not the dial pattern causing  
> the
> problem, I've turned on debugging and this is what I'm getting:
>
> Feb  2 20:20:46.305: ISDN Se0/3/0:23 Q931: Applying typeplan for sw- 
> type
> 0xD is 0x2 0x1, Calling num 2049757113
> Feb  2 20:20:46.305: ISDN Se0/3/0:23 Q931: Applying typeplan for sw- 
> type
> 0xD is 0x1 0x1, Called num 011448712002000
> Feb  2 20:20:46.309: ISDN Se0/3/0:23 Q931: TX -> SETUP pd = 8   
> callref =
> 0x30FB
>    Bearer Capability i = 0x8090A2
>        Standard = CCITT
>        Transfer Capability = Speech
>        Transfer Mode = Circuit
>        Transfer Rate = 64 kbit/s
>    Channel ID i = 0xA98390
>        Exclusive, Channel 16
>    Calling Party Number i = 0x2180, '2049757113'
>        Plan:ISDN, Type:National
>    Called Party Number i = 0x91, '011448712002000'
>        Plan:ISDN, Type:International
> Feb  2 20:20:46.405: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8
> callref = 0xB0FB
>    Cause i = 0x809C - Invalid number format (incomplete number)
> -----
>
> I also tried numbering-type international, with the same result:
>
> -----
>
>
> Feb  2 20:24:43.921: ISDN Se0/3/0:23 Q931: Applying typeplan for sw- 
> type
> 0xD is 0x2 0x1, Calling num 2049757113
> Feb  2 20:24:43.921: ISDN Se0/3/0:23 Q931: Applying typeplan for sw- 
> type
> 0xD is 0x1 0x1, Called num 011448712002000
> Feb  2 20:24:43.921: ISDN Se0/3/0:23 Q931: TX -> SETUP pd = 8   
> callref =
> 0x3100
>    Bearer Capability i = 0x8090A2
>        Standard = CCITT
>        Transfer Capability = Speech
>        Transfer Mode = Circuit
>        Transfer Rate = 64 kbit/s
>    Channel ID i = 0xA98390
>        Exclusive, Channel 16
>    Calling Party Number i = 0x2180, '2049757113'
>        Plan:ISDN, Type:National
>    Called Party Number i = 0x91, '011448712002000'
>        Plan:ISDN, Type:International
> Feb  2 20:24:44.025: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8
> callref = 0xB100
>    Cause i = 0x809C - Invalid number format (incomplete number)
>
> ---
>
> I tested this PRI on an Asterisk box and sending 011448712002000 works
> so I'm at a loss as to why the Cisco is having problems.
>
> Any suggestions?
>
>
> -- 
> John Lange
> http://www.johnlange.ca
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip