[cisco-voip] CCME ISDN2 (BRI) /DID failure

Tue Jan 5 07:25:38 EST 2010

Hi there,

Have you seen this before? there is no error in this config at least i think there isn't.
Is it my translation rules my dialpeers, or my BRI interface?
This config is driving me crazy all the way.

I've used 3xx extensions for the IP Phones

****Here is my show run output.****

CUCME#show running-config 
!
isdn switch-type basic-net3
!
!
!
voice service voip
!
voice class codec 1
 codec preference 1 g722-64
 codec preference 2 g711ulaw
!         
voice translation-rule 1
 rule 1 // /00/ type national national
 rule 2 // /000/ type international international
!
voice translation-rule 2
 rule 1 /^0\(.*\)/ /0\1/ type any unknown plan any unknown
 rule 2 /^7611153\(..$\)/ /3\1/
!
voice translation-rule 3
 rule 1 /^3\(..$\)/ /7611153/
!
!
voice translation-profile main-number-in
 translate calling 1
 translate called 2
!
voice translation-profile main-number-out
 translate calling 3
!
interface BRI0/3/0
 description Nummer 0761115300
 no ip address
 isdn switch-type basic-net3
 isdn overlap-receiving
 isdn point-to-point-setup
 isdn incoming-voice voice
 isdn sending-complete
 isdn static-tei 0
!
interface BRI0/3/1
 description Nummer 0761115300
 no ip address
 isdn switch-type basic-net3
 isdn overlap-receiving
 isdn point-to-point-setup
 isdn incoming-voice voice
 isdn sending-complete
 isdn static-tei 0
!     
!
dial-peer voice 399 pots
 description FAX
 destination-pattern 399
 port 0/1/0
!
!         
dial-peer voice 1 pots
 description Incomming 761115300-99
 translation-profile incoming main-number-in
 incoming called-number .
 direct-inward-dial
!
dial-peer voice 2 pots
 description Outgoing Default
 translation-profile outgoing main-number-out
 preference 1
 destination-pattern 0T
 port 0/3/0
!
dial-peer voice 3 pots
 description Outgoing Traffic Local
 translation-profile outgoing main-number-out
 destination-pattern 0[2-9]......
 port 0/3/0
 forward-digits 7
!
dial-peer voice 4 pots
 description Outgoing Traffic National
 translation-profile outgoing main-number-out
 destination-pattern 00[1-9]........
 port 0/3/0
 forward-digits 10
!
dial-peer voice 5 pots
 description Outgoing Traffic International
 translation-profile outgoing main-number-out
 destination-pattern 000.T
 port 0/3/0
 prefix 00
!
dial-peer voice 6 pots
 description Outgoing Mobile
 translation-profile outgoing main-number-out
 destination-pattern 006........
 port 0/3/0
 forward-digits 10
!
dial-peer voice 7 pots
 description Outgoing Traffic Emergency 
 translation-profile outgoing main-number-out
 destination-pattern 0112
 port 0/3/0
 forward-digits 3
!
dial-peer voice 8 pots
 description Outgoing Traffic Emergency 
 translation-profile outgoing main-number-out
 destination-pattern 112
 port 0/3/0
 forward-digits all
!
dial-peer voice 9 pots
 description Outgoing Traffic 0900
 translation-profile outgoing main-number-out
 destination-pattern 0090T
 port 0/3/0
 forward-digits all
!
!==============================================================================================================

****Here is my Debug ISDN Q9xx output. when i dial from 101419211(my office number) to 761115302 ( Customers number )****
*Jan  5 11:49:17.403: ISDN BR0/3/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan  5 11:49:17.403: ISDN BR0/3/0 Q921: S4_SABME: Sending UA
*Jan  5 11:49:17.403: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/3/0, TEI 0 changed to up
*Jan  5 11:49:17.403: ISDN BR0/3/0 Q921: User TX -> UAf sapi=0 tei=0
*Jan  5 11:49:17.467: ISDN BR0/3/0 Q921: User RX <- INFO sapi=0 tei=0, ns=0 nr=0
*Jan  5 11:49:17.467: ISDN BR0/3/0 Q931: SETUP pd = 8  callref = 0x35
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0x82
                Preferred, B2
        Progress Ind i = 0x8183 - Origination address is non-ISDN
        Calling Party Number i = 0x2181, '101419211'
                Plan:ISDN, Type:National
        Called Party Number i = 0xA1, '761115302'
                Plan:ISDN, Type:National
*Jan  5 11:49:17.467: ISDN BR0/3/0 Q921: User TX -> RR sapi=0 tei=0 nr=1
*Jan  5 11:49:17.479: ISDN BR0/3/0 Q921: User TX ->
CUCME(config)# INFO sapi=0 tei=0, ns=0 nr=1
*Jan  5 11:49:17.483: ISDN BR0/3/0 Q931: CALL_PROC pd = 8  callref = 0xB5
        Channel ID i = 0x8A
                Exclusive, B2
*Jan  5 11:49:17.499: ISDN BR0/3/0 Q921: User RX <- RR sapi=0 tei=0 nr=1
*Jan  5 11:49:17.499: ISDN BR0/3/0 Q921: User TX -> INFO sapi=0 tei=0, ns=1 nr=1
*Jan  5 11:49:17.499: ISDN BR0/3/0 Q931: DISCONNECT pd = 8  callref = 0xB5
        Cause i = 0x8081 - Unallocated/unassigned number
*Jan  5 11:49:17.515: ISDN BR0/3/0 Q921: User RX <- RR sapi=0 tei=0 nr=2
*Jan  5 11:49:17.675: ISDN BR0/3/0 Q921: User RX <- INFO sapi=0 tei=0, ns=1 nr=2
*Jan  5 11:49:17.675: ISDN BR0/3/0 Q931: RELEASE pd = 8  callref = 0x35
        Cause i = 0x8081 - Unallocated/unassigned number
*Jan  5 11:49:17.679: ISDN BR0/3/0 Q921: User TX -> RR sapi=0 tei=0 nr=2
*Jan  5 11:49:17.679: ISDN BR0/3/0 Q921: User TX -> INFO sapi=0 tei=0, ns=2 nr=2
*Jan  5 11:49:17.679: ISDN BR0/3/0 Q931: RELEASE_COMP pd = 8  callref = 0xB5
*Jan  5 11:49:17.695: ISDN BR0/3/0 Q921: User RX <- RR sapi=0 tei=0 nr=3
CUCME(config)#
CUCME(config)#
*Jan  5 11:49:27.699: ISDN BR0/3/0 Q921: User TX -> RRp sapi=0 tei=0 nr=2
*Jan  5 11:49:27.711: ISDN BR0/3/0 Q921: User RX <- RRf sapi=0 tei=0 nr=3
*Jan  5 11:49:27.871: ISDN BR0/3/0 Q921: User RX <- DISCp sapi=0 tei=0
*Jan  5 11:49:27.871: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0/3/0, TEI 0 changed to down
CUCME(config)#
*Jan  5 11:49:27.871: ISDN BR0/3/0 Q921: User TX -> UAf sapi=0 tei=0
*Jan  5 11:49:27.871: ISDN BR0/3/0 Q931: Ux_DLRelInd: DL_REL_IND received from L2

THanks
Vano,

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100105/68dd565e/attachment.html>