[cisco-voip] Trunk-group

[Aing Roda]

Hi Darel,

Here is my current configuration.

What I want to do is to separate E1 6/3 to send calls with different prefix. For example: calls to 77785515xxxxx to E1 7/2 and 7/3, calls to 77785511xxxxx to E1 6/3.

===================================================================================
controller E1 6/3
 framing NO-CRC4 
 pri-group timeslots 1-31 nfas_d none nfas_int 8 nfas_group 1
!
controller E1 7/2
 framing NO-CRC4 
 pri-group timeslots 1-31 nfas_d primary nfas_int 2 nfas_group 1
!
controller E1 7/3
 framing NO-CRC4 
 pri-group timeslots 1-31 nfas_d none nfas_int 3 nfas_group 1


interface Serial7/2:15
 description ######################## To TMIC ########################
 no ip address
 isdn switch-type primary-ni2c
 isdn not-end-to-end 56
 isdn incoming-voice modem
 isdn map address 008 plan isdn type national
 isdn rlm-group 1
 isdn T310 60000
 no isdn send-status-enquiry
 isdn send-alerting
 isdn negotiate-bchan resend-setup
 isdn sending-complete
 isdn outgoing-voice info-transfer-capability 3.1kHz-audio
 no cdp enable

rlm group 1
 protocol rlm port 3010
 server PGW2000-1
  link address 192.168.100.20 source FastEthernet0/0 weight 1

voice-port 7/2:D
 translation-profile incoming sixteen
 description ###### Voice Port for TMIC #######
 bearer-cap 3100Hz

dial-peer voice 28855 pots
 description To TMIC
 translation-profile outgoing three
 destination-pattern 777855[1][56]T
 progress_ind setup enable 3
 progress_ind alert enable 8
 progress_ind progress enable 8
 progress_ind connect enable 8
 direct-inward-dial
 port 7/2:D
 prefix 0
===============================================================================


Roda





________________________________
From: "Graham, Darel" <Darel.Graham at Globalcrossing.com>
To: Aing Roda <roda_3tel at yahoo.com>; "cisco-voip at puck.nether.net" <cisco-voip at puck.nether.net>
Sent: Mon, January 25, 2010 8:22:42 PM
Subject: RE: [cisco-voip] Trunk-group


Please post config sample.
 
In lieu of having the config sample, the best I can say is the following:
 
!
trunk group  [trunkgroupname]
!
!
controller T1 0/0/1
 framing esf
 linecode b8zs
 pri-group timeslots 1-24
!
!
interface Serial0/1/0:23
 no ip address
 encapsulation hdlc
 isdn switch-type primary-ni
 isdn incoming-voice voice
 no cdp enable
!
!
dial-peer voice 100 pots
 trunkgroup [trunkgroupname]
  destination-pattern .
 no digit-strip
 forward-digits all
!
 
 
 
Darel 
·  **This e-mail is strictly confidential and intended only for use by the addressee unless otherwise indicated**
From:cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Aing Roda
Sent: Monday, January 25, 2010 4:29 AM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Trunk-group
 
Hi,

Can anybody help me with this?

The following documentation tell me how use Trunk Group Dial Out Feature, which can be configured on Controller T1 or E1 interface. It is supported on Cisco AS5350, AS5400, and AS5850 Universal Gateways. However, when I go to Controller E1 interface configuration, the "trunk-group" command is not available. I am using Cisco AS5400 with IOS version 12.3(12). Does this version has the Trunk Group Dial Out Feature? If not, which IOS version should I use?

NOTE: In global and serial interface configuration, the "trunk-group" command is available.

http://www.cisco.com/en/US/docs/routers/access/as5350/software/release/notes/trnkgrpf.html

Here is how we connect AS5400 to other network.

VoIP Gateway ======(SIP/H323)=====> AS5400 (Softswitch) =======(SS7)======>PSTN


Roda


      
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100125/5e48def1/attachment.html>