[cisco-voip] Need Help on CME Installation

Wed Jan 27 16:30:00 EST 2010

I thought FXO was for connections coming from the telco & FXS were for
end-devices such as analog phones, fax machines, and modems.

Since the lines are coming from the telco to my router, wouldn't the
VIC2-4FXO card be the right card?

Hyoun Kim

Network Administrator I

Charter Media - East Division

640 Broadmor Blvd, Suite 80

Murfreesboro, TN 37129

Email: Hyoun.Kim at chartercom.com

Office: 615.217.6245

Fax: 615.217.6255

From: Matt Slaga (US) [mailto:Matt.Slaga at us.didata.com] 
Sent: Wednesday, January 27, 2010 2:58 PM
To: Kim, Hyoun S; cisco-voip at puck.nether.net
Subject: RE: Need Help on CME Installation

Someone can correct me if I am wrong, I run into FXO DID numbers about
once a few years.

I believe you would need VIC2-4FXS/DID cards to allow the incoming DTMF
DID indicators to come through properly.  Otherwise, the basic FXO cards
will not pick up the appropriate DTMF tones indicating what DID the call
is destined for.

You are definitely on the right track though!

From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Kim, Hyoun S
Sent: Wednesday, January 27, 2010 3:55 PM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Need Help on CME Installation

Some of you may remember me.  My employer has put me in charge of
installing Cisco VoIP solutions for various offices around the state.
I've installed 4 of them so far, roughly with 40-50 users at each
office.  I've been getting real comfortable with installing them but all
those offices utilized a PRI.  So configuration of the system was fairly
simple and if all was set up correctly, you could just unplug the PRI
from the old phone system and plug it into the Cisco router and
everything works just fine.

For my next office, things are somewhat different and I'm not sure how
to approach it.  I was told that the next office does not have a PRI.
I'm not 100% fluent in telephony, but their current Nortel system
utilizes 13 POTS lines, 1 BRI, and 4 trunk groups.  There are  15 DID
numbers each trunk group for a total of 60 DID numbers.

For the new router, (which is a C2821), I went ahead and requested 4
VIC2-4FXO cards.  Are these the right cards to get?  I didn't get the
BRI card because I'm going to see if the phone company can convert the
BRI to POTS lines to save some money.  So that should give me a total of
15 POTS lines to plug into my router.  

The DID numbers span from 9421 through 9480.  However, on the
information sheet, there are other numbers as well (which I'm assuming
are the actual POTS lines' numbers).  These numbers are all over the
place, such as 1101, 1103, 1119, 2562, 4400, etc.  When I dial them,
they are picked up by the Nortel automated system as if I were dialing
the direct line specified in the DID number range.  So my question is,
when I program the CME/CUE, do I just configure ephone-dn according to
the DID numbers and leave out those other numbers?  I'm just wondering
if the Telco forwards all these "other numbers" to that DID's "direct
line".  I know for the Autoattendent, you just use 1 number.

Is this the right way I should be going about this?

Thanks for any help and sorry for the long e-mail.

________________________________

Hyoun Kim * Network Administrator I - East Division

640 Broadmor Blvd * Suite 80 * Murfreesboro, TN 37129

' 615.217.6245 * ' 859.312.6941 * 7 615.217.6255 * * 
Hyoun.Kim at chartercom.com

E-MAIL CONFIDENTIALITY NOTICE: 

The contents of this e-mail message and 
any attachments are intended solely for the 
addressee(s) and may contain confidential 
and/or legally privileged information. If you 
are not the intended recipient of this message 
or if this message has been addressed to you 
in error, please immediately alert the sender
 by reply e-mail and then delete this message 
and any attachments. If you are not the 
intended recipient, you are notified that 
any use, dissemination, distribution, copying, 
or storage of this message or any attachment 
is strictly prohibited.

________________________________

Disclaimer: This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the designated
addressee(s) named above only. If you are not the intended addressee,
you are hereby notified that you have received this communication in
error and that any use or reproduction of this email or its contents is
strictly prohibited and may be unlawful. If you have received this
communication in error, please notify us immediately by replying to this
message and deleting it from your computer. Thank you. 

E-MAIL CONFIDENTIALITY NOTICE: 

The contents of this e-mail message and 
any attachments are intended solely for the 
addressee(s) and may contain confidential 
and/or legally privileged information. If you 
are not the intended recipient of this message 
or if this message has been addressed to you 
in error, please immediately alert the sender
 by reply e-mail and then delete this message 
and any attachments. If you are not the 
intended recipient, you are notified that 
any use, dissemination, distribution, copying, 
or storage of this message or any attachment 
is strictly prohibited.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100127/489a8338/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 1990 bytes
Desc: image001.jpg
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100127/489a8338/attachment.jpe>