[cisco-voip] sending calls form a voip dialpeer to another dialpeer

[Dew Swen]

Thanks Kapil,

I got everything clearly.

But just one thing: My gateway is configured as a normal H323 gateway 
and registers to CUCM. (provides SRST as call-manager-fallback). Do I 
need to configure anything special on the CUCM GW settings?

Regards,

-- 
Dew Swen
CCVP, CCNP


23.06.2010 11:53, kapil atrish yazmış:
> If everything is on LAN, you may send G.711 call from CUCM to GW, play 
> the prompt via TCL and send it back to CUCM (Pointing to Unity Pilot). 
> Unity does support G.711 and G.729 simultaneously, in case you wish to 
> send G.729 from CUCM to GW, play the prompt and send it back to Unity 
> (G.729) then definately you need Xcoder.
> You need to configure your router as CME and register Xcoder to this 
> in case you are doing G729-G711. You won't need additional MTP.
>
>
> --- On *Wed, 6/23/10, Dew Swen /<dew.swen at gmail.com>/* wrote:
>
>
>     From: Dew Swen <dew.swen at gmail.com>
>     Subject: Re: [cisco-voip] sending calls form a voip dialpeer to
>     another dialpeer
>     To: "kapil atrish" <nice_chatin at yahoo.com>
>     Cc: "Mac GroupStudy" <mac.groupstudy at gmail.com>,
>     "cisco-voip at puck.nether.net" <cisco-voip at puck.nether.net>
>     Date: Wednesday, June 23, 2010, 2:15 PM
>
>
>     Yes Kapil, I am playing a prompt and that forward call to Unity. I
>     play the prompt in g711 as you said.
>
>     Do I need to send call to CUCM (Unity's hunt pilot number) in a
>     g729 format? Unity talks g729. If it is like that I need xcoder.
>
>     What about MTP?
>
>     Regards,
>
>     -- 
>     Dew Swen
>     CCVP, CCNP
>
>
>
>     23.06.2010 11:02, kapil atrish yazmış:
>>
>>     Are you playing any prompts via TCL,  it supports only G.711 for
>>     voice prompts. Depending upon requirements you may need Xcoder on
>>     GW to get it working.
>>
>>     --- On *Wed, 6/23/10, Dew Swen /<dew.swen at gmail.com>/* wrote:
>>
>>
>>         From: Dew Swen <dew.swen at gmail.com>
>>         Subject: Re: [cisco-voip] sending calls form a voip dialpeer
>>         to another dialpeer
>>         To: "Mac GroupStudy" <mac.groupstudy at gmail.com>
>>         Cc: "cisco-voip at puck.nether.net" <cisco-voip at puck.nether.net>
>>         Date: Wednesday, June 23, 2010, 12:34 PM
>>
>>         Hi Mac,
>>
>>         Yes this command works for my 2821 router.
>>
>>         I need to send call to Unity with a tcl script. I got the
>>         call from CUCM (by using a translation pattern) with a voip
>>         dial-peer; after that I need to send this call to Unity with
>>         a voip dial-peer. That's why I need 2 voip dialpeer.
>>
>>         The main question is this?
>>
>>         "What else I need? MTP? Or any other tricks that I must do?"
>>
>>         Waiting for your suggestions.
>>
>>         Regards,
>>
>>         -- 
>>         Dew Swen
>>         CCVP, CCNP
>>
>>
>>
>>         23.06.2010 01:35, Mac GroupStudy yazmış:
>>>         If your router supports the command you don't even need a
>>>         CUBE. Try the command I referenced to see if it is supported
>>>         first. Also consider why you need to route from one VOIP DP
>>>         to another. A true CUBE solution maybe your best bet.
>>>
>>>         On Tue, Jun 22, 2010 at 4:02 PM, Dew Swen
>>>         <dew.swen at gmail.com
>>>         <http://us.mc550.mail.yahoo.com/mc/compose?to=dew.swen@gmail.com>>
>>>         wrote:
>>>
>>>             Other than cube what is needed?
>>>
>>>             Regards,
>>>
>>>             --
>>>             Dew Swen
>>>             CCVP, CCNP
>>>
>>>
>>>
>>>
>>>             On 22.Haz.2010, at 16:32, Mac GroupStudy
>>>             <mac.groupstudy at gmail.com
>>>             <http://us.mc550.mail.yahoo.com/mc/compose?to=mac.groupstudy@gmail.com>>
>>>             wrote:
>>>
>>>>             Prior to CUBE there was a concept of an IP-IP Gateway.
>>>>             It and CUBE requires something similar to this:
>>>>             config)# voice service voip
>>>>             # allow-connections h323 to h323
>>>>
>>>>
>>>>             On Tue, Jun 22, 2010 at 8:41 AM, Dew Swen
>>>>             <dew.swen at gmail.com
>>>>             <http://us.mc550.mail.yahoo.com/mc/compose?to=dew.swen@gmail.com>>
>>>>             wrote:
>>>>
>>>>                 Could anyone shed on some light about:
>>>>
>>>>                 "What is needed for sending calls from a voip
>>>>                 dial-peer to voip dial-peer in a h323 gw?"
>>>>
>>>>                 AFAIK,
>>>>                 - CUBE functions must be enabled
>>>>                 - MTP must be configured on both CUCM and IOS
>>>>                 - Have to do something in CUCM Gateway configuration??
>>>>
>>>>                 Any help or document will be appriciated.
>>>>
>>>>                 Kind regards,
>>>>
>>>>                 -- 
>>>>                 Dew Swen
>>>>                 CCVP, CCNP
>>>>
>>>>
>>>>                 _______________________________________________
>>>>                 cisco-voip mailing list
>>>>                 cisco-voip at puck.nether.net
>>>>                 <http://us.mc550.mail.yahoo.com/mc/compose?to=cisco-voip@puck.nether.net>
>>>>                 https://puck.nether.net/mailman/listinfo/cisco-voip
>>>>
>>>>
>>>
>>
>>
>>         -----Inline Attachment Follows-----
>>
>>         _______________________________________________
>>         cisco-voip mailing list
>>         cisco-voip at puck.nether.net
>>         <http://us.mc550.mail.yahoo.com/mc/compose?to=cisco-voip@puck.nether.net>
>>         https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>>
>
>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100623/083899e3/attachment.html>