[cisco-voip] CCM SIP connection to B2B getting fast busy

[Nick Matthews]

I'm still confused on what you mean by no SIP invite.

It's possible that the huawei only supports UDP SIP and it's not
completing the 3 way TCP handshake.  You can change that under the SIP
profiles to be UDP only.

Otherwise, check that huawei has routing back to the IP of your CUCM,
and firewalls aren't involved.

-nick

On Thu, Mar 4, 2010 at 3:38 AM, Jefflin Choi <jefflin.choi at gmail.com> wrote:
> Hi,
>
> Thanks for all the reply.
>
> Tried placing the a CUBE in the middle and seems like there is already SIP
> invite being sent. Too bad the huawei isn't full configured yet to determine
> if all is ok.
>
> I was wondering....I tried to make a test call using SIP trunk directly to
> the B2B SBC and no sip invite. But i did get sip invite when i pointed it to
> the cube.
> All i can see on the sniff trace from CCM to B2B is:
> TCP 35472 > sip [SYN] seq=0 Win 5840 Len=0 MSS=1460 TSV=82731827 TSER=0 WS=2
>
> In fact i just changed the ip of the CUBE to the B2B SBC to make sure
> configs are exactly the same but no sip invite unlike when it is pointed to
> the CUBE. Is this normal? Any thoughts?
>
> Thanks,
> Jeff
>
>
>
> On Thu, Mar 4, 2010 at 1:10 AM, Mark Holloway <mh at markholloway.com> wrote:
>>
>> You most certainly need CUBE.  You can find the CUBE guide for sip-to-sip
>> here.
>>
>> http://www.cisco.com/en/US/docs/ios/voice/cube/configuration/guide/vb-gw-sipsip.html
>>
>>
>> On Mar 3, 2010, at 7:18 AM, Jefflin Choi wrote:
>>
>> I see. So a router in the middle is required then. Doesn't the CCM7
>> support it without the CUBE?
>>
>> Thanks.
>>
>> On Wed, Mar 3, 2010 at 9:48 PM, Dennis Heim <Dennis.Heim at cdw.com> wrote:
>>>
>>> You will probably end up having to use CUBE, instead of terminating the
>>> trunk to CCM.
>>>
>>>
>>>
>>> Dennis Heim
>>> Network Voice Engineer
>>> CDW  Advanced Technology Services
>>> 11711 N. Meridian Street, Suite 225
>>> Carmel, IN  46032
>>>
>>> 317.569.4255 Office
>>> 317.569.4201 Fax
>>> 317.694.6070 Cell
>>>
>>> dennis.heim at cdw.com
>>> www.berbee.com
>>>
>>>
>>>
>>> From: cisco-voip-bounces at puck.nether.net
>>> [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jefflin Choi
>>> Sent: Wednesday, March 03, 2010 8:31 AM
>>> To: cisco-voip at puck.nether.net
>>> Subject: [cisco-voip] CCM SIP connection to B2B getting fast busy
>>>
>>>
>>>
>>> Hi,
>>>
>>> I'm trying to configure a SIP connection to a 3rd party B2B SIP device,
>>> then B2B will relay to a Huawei (SIP) device on the other end.
>>> topology:
>>> IP Phones ------CCM7 -------(provider)--B2B---------Huawei---pstn
>>>
>>> configuration:
>>> CCM is configured with SIP trunk with ip address of the B2B and route
>>> pattern uses the SIP trunk configured.  MTP required uncheck as of the
>>> moment.  codec G711uLaw and No authentication required.
>>>
>>> Problem:
>>> Outgoing call from IP Phone to PSTN gets fast busy signal.  When placed a
>>> sniffer in between CCM7 and B2B gateway, i didnt see any sip invite
>>> initiated by the CCM7. CCM7 and ip phones only have traffic reachability to
>>> B2B but not Huawei.
>>> The provider (B2B to pstn) was tested using altitude(as claimed by the
>>> customer) and works fine but we are testing using CCM7.
>>>
>>> Question:
>>> 1> Am i right to use CCM trunk to connect to the B2B sip?
>>> 2> Any additional configs i need to configure? Misconfiguration?
>>> 3>Should i expect SIP invite to be sent by CCM when call is triggered by
>>> ip phones?
>>>
>>> Thanks,
>>> Jeff
>>
>> _______________________________________________
>> cisco-voip mailing list
>> cisco-voip at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>