[cisco-voip] help with WS-SVC-CMM-6T1

[ccieid1ot]

You are having a layer 1 issue.  Maybe bad card?  Did you no shut the
controllers?  The intereface settings overrides what's in global
settings.

On Mon, Mar 8, 2010 at 6:38 PM, Frank Arrasmith
<frank.arrasmith at gmail.com> wrote:
> config is for MGCP.  Not having much experience with the CMM, i stared and
> compared from a production CMM module with the same config. I know the
> running config doesnt necessarily show all the settings, but that and the
> guide were my only reference. switch type was primary-ni, production and lab
> devices both have T1's from teh same carrier, so I duplicated that in the
> lab device as well.  One of the things Im not sure about is the difference
> between the global config switch-type and the interface config of switch
> type. Now that I think about it, i did not check the global setting, only
> the interface setting...
>
> On Mon, Mar 8, 2010 at 5:01 PM, Scott Voll <svoll.voip at gmail.com> wrote:
>>
>> MGCP or H323?
>> !
>> controller T1 0/0/0
>>  clock source line primary
>>  pri-group timeslots 1-24 <-- I'm guessing maybe the timeslots?
>> Switch type?
>>
>>
>> Scott
>>
>>
>> On Mon, Mar 8, 2010 at 2:53 PM, Frank Arrasmith
>> <frank.arrasmith at gmail.com> wrote:
>>>
>>> Hi all,
>>>     I am trying to configure a  6 port T1 module in a CMM, and am
>>> thoroughly stumped.  I have a T1 drop that was tested good and comes up when
>>> connected to a 3800 with a T1 VWIC card.   The T1 will not come up to any of
>>> the ports on the 6T1 module on the CMM.  The Controller configs are
>>> identical on the router and the CMM.  I get a green LED on the CMM card but
>>> thats it.  The weird part is that the router T1 will come up to the carrier
>>> T1, a T1 loopback, and even the T1 connected to the CMM module with a
>>> crossover T1 cable.   The CMM module will not come up to a loopback, nor the
>>> Router t1, nor the carrier t1(but the LED will green up).  I could not find
>>> any documentation on a different Pinout for CMM module, so my guess is I am
>>> missing something in the config.  Is there anything special needed for these
>>> CMM modules, or anybody have a suggestion on a command to troubleshoot the
>>> Layer 1 issue?
>>>
>>> Config for CMM:
>>> #show controllers t1 1/0 brief
>>> T1 1/0 is down.
>>>   Applique type is Channelized T1
>>>   Cablelength is long gain36 0db
>>>   Receiver has loss of signal.
>>>   alarm-trigger is not set
>>>   Soaking time: 3, Clearance time: 10
>>>   AIS State:Clear  LOS State:Clear  LOF State:Clear
>>>   Framing is ESF, Line Code is B8ZS, Clock Source is Line.
>>>
>>> #show int se1/0:23
>>> Serial1/0:23 is reset, line protocol is down
>>>   Hardware is DSX1
>>>   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
>>>      reliability 255/255, txload 1/255, rxload 1/255
>>>   Encapsulation HDLC, loopback not set
>>>
>>> #show isdn status
>>> Global ISDN Switchtype = primary-ni
>>> ISDN Serial1/0:23 interface
>>>         dsl 0, interface ISDN Switchtype = primary-ni
>>>     Layer 1 Status:
>>>         DEACTIVATED
>>>     Layer 2 Status:
>>>         TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
>>>     Layer 3 Status:
>>>         0 Active Layer 3 Call(s)
>>>     Active dsl 0 CCBs = 0
>>>     The Free Channel Mask:  0x00000000
>>>     Number of L2 Discards = 0, L2 Session ID = 0
>>>
>>>
>>> Config for the T1 VWIC:
>>> #show controllers t1 0/1/0 brief
>>> T1 0/1/0 is up.
>>>   Applique type is Channelized T1
>>>   Cablelength is long gain36 0db
>>>   No alarms detected.
>>>   alarm-trigger is not set
>>>   Soaking time: 3, Clearance time: 10
>>>   AIS State:Clear  LOS State:Clear  LOF State:Clear
>>>   Version info Firmware: 20040802, FPGA: 13, spm_count = 0
>>>   Framing is ESF, Line Code is B8ZS, Clock Source is Line.
>>>
>>> Serial0/1/0:23 is up, line protocol is up (spoofing)
>>>   Hardware is DSX1
>>>   MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
>>>      reliability 255/255, txload 1/255, rxload 1/255
>>>   Encapsulation HDLC, loopback not set
>>>
>>> ISDN Serial0/1/0:23 interface
>>>         dsl 0, interface ISDN Switchtype = primary-ni
>>>         L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003
>>>     Layer 1 Status:
>>>         ACTIVE
>>>     Layer 2 Status:
>>>         TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
>>>     Layer 3 Status:
>>>         0 Active Layer 3 Call(s)
>>>     Active dsl 0 CCBs = 0
>>>     The Free Channel Mask:  0x807FFFFF
>>>     Number of L2 Discards = 0, L2 Session ID = 23
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> cisco-voip mailing list
>>> cisco-voip at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-voip
>>>
>>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>