[cisco-voip] AT&T/Avaya Definity G3 connection
Mac GroupStudy
mac.groupstudy at gmail.com
Wed Sep 29 20:33:38 EDT 2010
QSig trunk fixed MWI issues I was having between an Avaya and Cisco
integration a few years back at Honda of SC.
On Tue, Sep 28, 2010 at 5:15 PM, Wes Sisk <wsisk at cisco.com> wrote:
> I believe pbx configs as well as versions are covered in the interop
> portal:
>
> http://www.cisco.com/en/US/solutions/ns340/ns414/ns728/networking_solutions_products_genericcontent0900aecd805b561d.html
>
> /Wes
>
> Charles Goldsmith wrote:
>
> Thanks Tim, however, this is an older Definity G3, running v9 software, but
> that doesn't seem to affect things, as my Avaya support tells me that it
> wouldn't matter if I updated or not.
>
> One thing I neglected in my info was that I'm MGCP on CM 8.0.2
>
> One suggestion I found while googling was to set up the PRI as QSIG
> between the two, I'll try that tonight and see what happens.
>
> Thanks
> Charles
>
> On Tue, Sep 28, 2010 at 2:46 PM, Estes, Timothy <TimothyEstes at sfngroup.com
> > wrote:
>
>> I have some Cisco GWs to Avaya PRIs and calling name does work on calls
>> from the Avaya to Cisco. I have pasted the Cisco and Avaya configs below.
>>
>> UCM 8.0.3 with 3845 using H.323
>>
>>
>>
>> Avaya S8500 - R013x.00.1.346.0
>>
>>
>>
>>
>>
>> On the Cisco 3845 GW
>>
>>
>>
>> controller T1 0/1/0
>>
>> framing esf
>>
>> clock source internal
>>
>> linecode b8zs
>>
>> pri-group timeslots 1-24
>>
>> description Cable to Avaya S8500
>>
>>
>>
>> interface Serial0/1/0:23
>>
>> description PRI to Avaya S8500
>>
>> no ip address
>>
>> encapsulation hdlc
>>
>> no logging event link-status
>>
>> isdn switch-type primary-ni
>>
>> isdn protocol-emulate network
>>
>> isdn incoming-voice voice
>>
>> isdn outgoing display-ie
>>
>> no cdp enable
>>
>>
>>
>> dial-peer voice 7207 pots
>>
>> description AvayaS8500
>>
>> destination-pattern 016.T
>>
>> direct-inward-dial
>>
>> port 0/1/0:23
>>
>>
>>
>>
>>
>>
>>
>> On the Avaya trunk config -
>>
>>
>>
>> TRUNK GROUP
>>
>>
>>
>> Group Number: 17 Group Type: isdn CDR Reports:
>> y
>>
>> Group Name: Cisco to VoIP COR: 95 TN: 1 TAC:
>> 1517
>>
>> Direction: two-way Outgoing Display? n Carrier Medium:
>> PRI/BRI
>>
>> Dial Access? n Busy Threshold: 23 Night Service:
>>
>> Queue Length: 0
>>
>> Service Type: public-ntwrk Auth Code? n TestCall ITC:
>> rest
>>
>> Far End Test Line No:
>>
>> TestCall BCC: 4
>>
>> TRUNK PARAMETERS
>>
>> Codeset to Send Display: 6 Codeset to Send National IEs: 6
>>
>> Max Message Size to Send: 260 Charge Advice: none
>>
>> Supplementary Service Protocol: a Digit Handling (in/out):
>> enbloc/enbloc
>>
>>
>>
>> Trunk Hunt: cyclical
>>
>> Digital Loss Group: 13
>>
>> Incoming Calling Number - Delete: Insert: Format:
>> pub-unk
>>
>> Bit Rate: 1200 Synchronization: async Duplex:
>> full
>>
>> Disconnect Supervision - In? y Out? n
>>
>> Answer Supervision Timeout: 0
>>
>>
>>
>>
>>
>> TRUNK FEATURES
>>
>> ACA Assignment? n Measured: none Wideband
>> Support? n
>>
>> Maintenance
>> Tests? y
>>
>> Data Restriction? n NCA-TSC Trunk
>> Member:
>>
>> Send Name: y Send Calling
>> Number: y
>>
>> Used for DCS? n
>>
>> Suppress # Outpulsing? n Format: unk-pvt
>>
>> Outgoing Channel ID Encoding: preferred UUI IE Treatment:
>> service-provider
>>
>>
>>
>> Replace Restricted
>> Numbers? n
>>
>> Replace Unavailable
>> Numbers? n
>>
>> Send Connected
>> Number: y
>>
>> Network Call Redirection: none Hold/Unhold
>> Notifications? n
>>
>> Send UUI IE? y Modify Tandem Calling
>> Number? n
>>
>> Send UCID? y
>>
>> Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation?
>> n
>>
>>
>>
>> US NI Delayed Calling Name
>> Update? y
>>
>>
>>
>> Network (Japan) Needs Connect Before
>> Disconnect? n
>>
>>
>>
>>
>>
>>
>>
>> Hope this helps -
>>
>>
>>
>> Timothy Estes
>>
>> Network Engineer
>>
>> SFN Group
>>
>> Ft. Lauderdale FL
>>
>> timothyestes at sfngroup.com
>>
>>
>>
>>
>>
>> *From:* cisco-voip-bounces at puck.nether.net [mailto:
>> cisco-voip-bounces at puck.nether.net] *On Behalf Of *Charles Goldsmith
>> *Sent:* Tuesday, September 28, 2010 11:56 AM
>> *To:* voip puck
>> *Subject:* [cisco-voip] AT&T/Avaya Definity G3 connection
>>
>>
>>
>> We have a legacy Definity G3 system that I have a pair of PRI's connected
>> to, everything works except properly caller-id name info. I know the
>> Definity will send it, we used to have a Mitel 3300 connected to it that
>> would receive it just fine.
>>
>>
>>
>> I get number only on the Cisco phones, and interesting enough, with a
>> supervised transfer from the Definity attendant console,
>> the initial connection shows up as Unknown Caller, which is annoying for our
>> operators.
>>
>>
>>
>> Definity support told me that the issue was an incompatibility of IE
>> between the two systems.
>>
>>
>>
>> Has anyone else come across this, and did you find a work around or a way
>> to solve it? We'll hopefully replace the Definity with Cisco next year, but
>> that isn't set in stone and I'd like to solve this problem.
>>
>>
>>
>> Thanks
>>
>> Charles
>>
>
> ------------------------------
>
> _______________________________________________
> cisco-voip mailing listcisco-voip at puck.nether.nethttps://puck.nether.net/mailman/listinfo/cisco-voip
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100929/06864c03/attachment.html>
More information about the cisco-voip
mailing list