[cisco-voip] AT&T/Avaya Definity G3 connection
Wes Sisk
wsisk at cisco.com
Tue Sep 28 17:15:18 EDT 2010
I believe pbx configs as well as versions are covered in the interop portal:
http://www.cisco.com/en/US/solutions/ns340/ns414/ns728/networking_solutions_products_genericcontent0900aecd805b561d.html
/Wes
Charles Goldsmith wrote:
> Thanks Tim, however, this is an older Definity G3, running v9
> software, but that doesn't seem to affect things, as my Avaya support
> tells me that it wouldn't matter if I updated or not.
>
> One thing I neglected in my info was that I'm MGCP on CM 8.0.2
>
> One suggestion I found while googling was to set up the PRI as QSIG
> between the two, I'll try that tonight and see what happens.
>
> Thanks
> Charles
>
> On Tue, Sep 28, 2010 at 2:46 PM, Estes, Timothy
> <TimothyEstes at sfngroup.com <mailto:TimothyEstes at sfngroup.com>> wrote:
>
> I have some Cisco GWs to Avaya PRIs and calling name does work on
> calls from the Avaya to Cisco. I have pasted the Cisco and Avaya
> configs below.
>
> UCM 8.0.3 with 3845 using H.323
>
>
>
> Avaya S8500 - R013x.00.1.346.0
>
>
>
>
>
> On the Cisco 3845 GW
>
>
>
> controller T1 0/1/0
>
> framing esf
>
> clock source internal
>
> linecode b8zs
>
> pri-group timeslots 1-24
>
> description Cable to Avaya S8500
>
>
>
> interface Serial0/1/0:23
>
> description PRI to Avaya S8500
>
> no ip address
>
> encapsulation hdlc
>
> no logging event link-status
>
> isdn switch-type primary-ni
>
> isdn protocol-emulate network
>
> isdn incoming-voice voice
>
> isdn outgoing display-ie
>
> no cdp enable
>
>
>
> dial-peer voice 7207 pots
>
> description AvayaS8500
>
> destination-pattern 016.T
>
> direct-inward-dial
>
> port 0/1/0:23
>
>
>
>
>
>
>
> On the Avaya trunk config -
>
>
>
> TRUNK GROUP
>
>
>
> Group Number: 17 Group Type: isdn CDR
> Reports: y
>
> Group Name: Cisco to VoIP COR: 95 TN:
> 1 TAC: 1517
>
> Direction: two-way Outgoing Display? n Carrier
> Medium: PRI/BRI
>
> Dial Access? n Busy Threshold: 23 Night Service:
>
> Queue Length: 0
>
> Service Type: public-ntwrk Auth Code? n
> TestCall ITC: rest
>
> Far End Test Line No:
>
> TestCall BCC: 4
>
> TRUNK PARAMETERS
>
> Codeset to Send Display: 6 Codeset to Send National
> IEs: 6
>
> Max Message Size to Send: 260 Charge Advice: none
>
> Supplementary Service Protocol: a Digit Handling (in/out):
> enbloc/enbloc
>
>
>
> Trunk Hunt: cyclical
>
> Digital Loss
> Group: 13
>
> Incoming Calling Number - Delete: Insert:
> Format: pub-unk
>
> Bit Rate: 1200 Synchronization: async
> Duplex: full
>
> Disconnect Supervision - In? y Out? n
>
> Answer Supervision Timeout: 0
>
>
>
>
>
> TRUNK FEATURES
>
> ACA Assignment? n Measured: none
> Wideband Support? n
>
>
> Maintenance Tests? y
>
> Data Restriction? n NCA-TSC
> Trunk Member:
>
> Send Name: y Send
> Calling Number: y
>
> Used for DCS? n
>
> Suppress # Outpulsing? n Format: unk-pvt
>
> Outgoing Channel ID Encoding: preferred UUI IE Treatment:
> service-provider
>
>
>
> Replace
> Restricted Numbers? n
>
> Replace
> Unavailable Numbers? n
>
> Send
> Connected Number: y
>
> Network Call Redirection: none Hold/Unhold
> Notifications? n
>
> Send UUI IE? y Modify Tandem
> Calling Number? n
>
> Send UCID? y
>
> Send Codeset 6/7 LAI IE? y Ds1 Echo
> Cancellation? n
>
>
>
> US NI Delayed Calling
> Name Update? y
>
>
>
> Network (Japan) Needs Connect Before
> Disconnect? n
>
>
>
>
>
>
>
> Hope this helps -
>
>
>
> Timothy Estes
>
> Network Engineer
>
> SFN Group
>
> Ft. Lauderdale FL
>
> timothyestes at sfngroup.com <mailto:timothyestes at sfngroup.com>
>
>
>
>
>
> *From:* cisco-voip-bounces at puck.nether.net
> <mailto:cisco-voip-bounces at puck.nether.net>
> [mailto:cisco-voip-bounces at puck.nether.net
> <mailto:cisco-voip-bounces at puck.nether.net>] *On Behalf Of
> *Charles Goldsmith
> *Sent:* Tuesday, September 28, 2010 11:56 AM
> *To:* voip puck
> *Subject:* [cisco-voip] AT&T/Avaya Definity G3 connection
>
>
>
> We have a legacy Definity G3 system that I have a pair of PRI's
> connected to, everything works except properly caller-id name
> info. I know the Definity will send it, we used to have a Mitel
> 3300 connected to it that would receive it just fine.
>
>
>
> I get number only on the Cisco phones, and interesting enough,
> with a supervised transfer from the Definity attendant console,
> the initial connection shows up as Unknown Caller, which is
> annoying for our operators.
>
>
>
> Definity support told me that the issue was an incompatibility of
> IE between the two systems.
>
>
>
> Has anyone else come across this, and did you find a work around
> or a way to solve it? We'll hopefully replace the Definity with
> Cisco next year, but that isn't set in stone and I'd like to solve
> this problem.
>
>
>
> Thanks
>
> Charles
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20100928/5a7658fc/attachment.html>
More information about the cisco-voip
mailing list