[cisco-voip] New to Cisco Voice - Need to Setup Fax

[Haas, Neal]

COOL!!!!!! We will need to try this out. Thanks

Neal Haas

From: Lelio Fulgenzi [mailto:lelio at uoguelph.ca]
Sent: Wednesday, August 03, 2011 7:28 AM
To: Haas, Neal
Cc: Alex Lindsay; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] New to Cisco Voice - Need to Setup Fax

The "word" is, IOS v15 can give you SG3 speeds again on analog devices... haven't tried it yet though, we're still using 6608s in our core. :(

---
Lelio Fulgenzi, B.A.
Senior Analyst (CCS) * University of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Cooking with unix is easy. You just sed it and forget it.
                              - LFJ (with apologies to Mr. Popeil)

________________________________
From: "Neal Haas" <nhaas at co.fresno.ca.us<mailto:nhaas at co.fresno.ca.us>>
To: "Alex Lindsay" <alex at wavetechs.com<mailto:alex at wavetechs.com>>, "cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>" <cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>>
Sent: Wednesday, August 3, 2011 10:17:36 AM
Subject: Re: [cisco-voip] New to Cisco Voice - Need to Setup Fax


To be frank the easiest way to do FAX is to put them on to standard POTS. I wish I had

We have used ATA187 (Just will hang up –but  there is a new firm ware), VG224 (works OK),VG204(Works OK). You may want to look into a solution like Genifax if you can. If you do use an analog solution you will need to turn off error correction on the faxes and set the baud rate to 14.4 or lower.

If you use SIP see if you can use the T.38 protocol, we are going SIP in 60 days.

Neal Haas

From: cisco-voip-bounces at puck.nether.net<mailto:cisco-voip-bounces at puck.nether.net> [mailto:cisco-voip-bounces at puck.nether.net]<mailto:[mailto:cisco-voip-bounces at puck.nether.net]> On Behalf Of Alex Lindsay
Sent: Wednesday, August 03, 2011 7:00 AM
To: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: [cisco-voip] New to Cisco Voice - Need to Setup Fax

Hello,

I have a small MetroE network and I would like to consolidate my Faxing as I have done with my Voice.  I have a 7200vxr with VXB T1 card to connect to my PRI (that I got with the anticipation of fax oIP, to be frank, sucking).  Am starting to use that same PRI for in LATA calls managed by my local SBC but my primary LD is sent to a ITSP via SIP.

My question and thoughts are as follows;  What is the simplest solution to support about 25 Fax attached ATA’s (spa8000, spa2102 & Audiocodes MP-2032) to the voice gateway (PRI router)?  I was thinking of setting up a Cisco 2821 (that I already have) with a PVDM2-32/64 and CME 4.3/7 with a SIP trunk to the voice gateway.

Forgive my ignorance.  I am a diehard R&S guy and got through into the Voice world.


•         Do I need to PVDM2 if I am doing only SIP to SIP?

•         Does that version of CME support T.38 well or at all?

•         What is this Fax Relay all about and do I need it? I am reading mixed reviews.

Thank you for any advice, help or information.


My Regards,

Alexander A. Lindsay
WaveTech Systems
http://wavetechs.com<http://wavetechs.com/>
O: 305.224.1563
F: 305.865.0622
C: 305.903.7592
alex at wavetechs.com<mailto:alex at wavetechs.com>


_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110803/37c96e25/attachment.html>