[cisco-voip] Integrating 9971 with Polycom MCU

Wed Mar 16 17:50:42 EDT 2011

As stated you might be able to both dial into a MCU (Tandbergy Codian).  Researching this.

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Jason Aarons (US)
Sent: Wednesday, March 16, 2011 5:33 PM
To: Scott Voll; Ruben Trujillo
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Integrating 9971 with Polycom MCU

The Tandberg VCS has a list of supported endpoints. The 9971 is not a supported endpoint.

http://www.cisco.com/en/US/docs/telepresence/infrastructure/vcs/release_note/Cisco_VCS_Release_Note_X6.pdf

You would have to register the 9971 via SIP/H323 with the Tandberg VCS (effectively) removing it from CallManager.

I would expect long term to see the Tandberg VCS features moved into CallManager, or a SIP trunk between VCS/CallManager for multipoint video.

I don't think the intent of the 9971 in development was a multipoint conference, but a point-to-point Video Call. Similar to 7985. Just a guess.

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Scott Voll
Sent: Wednesday, March 16, 2011 5:11 PM
To: Ruben Trujillo
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Integrating 9971 with Polycom MCU

To my knowledge the Polycom MCU will not act as a Conference resource with CM.  you would need a cisco / tandberg in order to do that.

With the polycom you would need to have each endpoint call the MCU and enter the same conference.

am I misunderstanding?

Scott
On Wed, Mar 16, 2011 at 1:59 PM, Ruben Trujillo <rtrujill at adobe.com<mailto:rtrujill at adobe.com>> wrote:
Hi Scott,

Thanks for the info.  I've created the h323 gateway using the IP address of the Polycom MCU as well as a route pattern that uses that gateway under the "Gateway/Route List" field.  I get a fast busy though when I attempt to dial a Polycom endpoint though.

Thanks,
Ruben Trujillo
IT Telecom

From: Scott Voll [mailto:svoll.voip at gmail.com<mailto:svoll.voip at gmail.com>]
Sent: Wednesday, March 16, 2011 1:31 PM
To: Ruben Trujillo
Cc: cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
Subject: Re: [cisco-voip] Integrating 9971 with Polycom MCU

not sure about the 9971 but the 7961 with Video we have our polycom RMX2000 setup as a h323 gateway with a route pattern setup.  you dial the route and then enter your conference ID.

Scott
On Wed, Mar 16, 2011 at 9:35 AM, Ruben Trujillo <rtrujill at adobe.com<mailto:rtrujill at adobe.com>> wrote:
Hello,

Does anyone have any info on how to get a Cisco 9971 working with a Polycom MCU?

Thanks,
Ruben

[cid:image001.png at 01CBE402.AB3ED3C0]

Ruben Trujillo
Telecom Engineer
Adobe Systems

408.536.6006<tel:408.536.6006> (tel)
415.407.1646<tel:415.407.1646> (cell)
rtrujill at adobe.com<mailto:rtrujill at adobe.com>

345 Park Ave
San Jose, CA. 95110
www.adobe.com<http://www.adobe.com>

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net<mailto:cisco-voip at puck.nether.net>
https://puck.nether.net/mailman/listinfo/cisco-voip

________________________________
[http://image.exct.net/lib/feed16797d620d/i/2/8c665b10-9.gif]<http://dimensiondata.stream57.com/04141pm/>

Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, you are hereby notified that you have received this communication in error and that any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you.

-----------------------------------------
Disclaimer:

This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only.  If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful.  If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110316/d394fe33/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 871 bytes
Desc: image001.png
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20110316/d394fe33/attachment.png>