[cisco-voip] dial-peer
Цэвээндорж
tseveendorj at gmail.com
Tue Nov 15 03:52:11 EST 2011
Hi,
configuration of R2 and E1 port are working now. And I also configured
dial-peer for incoming and outgoing see it below
controller E1 2/2
framing NO-CRC4
ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani
dial-peer voice 2 pots
incoming called-number .
no digit-strip
direct-inward-dial
port 2/2:1
!
dial-peer voice 1626 voip
description to SYSmaster
destination-pattern 1626
voice-class codec 2
session target ipv4:x.x.x.x IP address modified
but when I dialed to access number 1626 then I got log from debug
debug voip dialpeer inout is ON (filter is OFF)
> .Nov 15 16:27:16.484 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Calling Number=11319722, Called Number=1626,
> Voice-Interface=0x69E1D254,
> Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
> Type=PEER_TYPE_VOICE,
> Peer Info Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.484 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=2
> .Nov 15 16:27:16.484 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Calling Number=11319722, Called Number=1626, Voice-Interface=0x0,
> Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
> Type=PEER_TYPE_VOICE,
> Peer Info Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.484 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=2
> .Nov 15 16:27:16.484 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Calling Number=11319722, Called Number=1626,
> Voice-Interface=0x69E1D254,
> Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
> Type=PEER_TYPE_VOICE,
> Peer Info Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.484 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=2
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersCore:
> Calling Number=, Called Number=1626, Peer Info
> Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersCore:
> Match Rule=DP_MATCH_DEST; Called Number=1626
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersCore:
> Result=Success(0) after DP_MATCH_DEST
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersMoreArg:
> Result=SUCCESS(0)
> List of Matched Outgoing Dial-peer(s):
> 1: Dial-peer Tag=1626
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Calling Number=1626, Called Number=1626, Peer Info
> Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Match Rule=DP_MATCH_DEST; Called Number=1626
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Result=Success(0) after DP_MATCH_DEST
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:
> Result=SUCCESS(0)
> List of Matched Outgoing Dial-peer(s):
> 1: Dial-peer Tag=1626
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Calling Number=1626, Called Number=1626, Peer Info
> Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Match Rule=DP_MATCH_DEST; Called Number=1626
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Result=Success(0) after DP_MATCH_DEST
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:
> Result=SUCCESS(0)
> List of Matched Outgoing Dial-peer(s):
> 1: Dial-peer Tag=1626
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Calling Number=, Called Number=1626, Peer Info
> Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Match Rule=DP_MATCH_DEST; Called Number=1626
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
> Result=Success(0) after DP_MATCH_DEST
> .Nov 15 16:27:16.548 GMT: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:
> Result=SUCCESS(0)
> List of Matched Outgoing Dial-peer(s):
> 1: Dial-peer Tag=1626
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersCore:
> Calling Number=, Called Number=1626, Peer Info
> Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersCore:
> Match Rule=DP_MATCH_DEST; Called Number=1626
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersCore:
> Result=Success(0) after DP_MATCH_DEST
> .Nov 15 16:27:16.548 GMT: //-1/76025A0C99C2/DPM/dpMatchPeersMoreArg:
> Result=SUCCESS(0)
> List of Matched Outgoing Dial-peer(s):
> 1: Dial-peer Tag=1626
> .Nov 15 16:27:16.932 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Calling Number=11319722, Called Number=1626,
> Voice-Interface=0x69E1D254,
> Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
> Type=PEER_TYPE_VOICE,
> Peer Info Type=DIALPEER_INFO_SPEECH
> .Nov 15 16:27:16.932 GMT:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
> Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=2
but nothing on my sysmaster gateway.
Question :
Do I hear IVR from sysmaster gateway when I set this configuration on
cisco gateway ?
Regards,
Tseveen
On 11/15/2011 15:44, Abebe Amare wrote:
> Hi,
>
> To configure the E1 port for R2 signalling,
>
> AS5350(config)#*controller e1 0/0*
> AS5350(config-controller)#*ds0-group 1 timeslots 1-30 type r2-analog r2-compelled ani*
>
>
>
> the R2 signalling type depends on your PSTN connection.
> Configure the dial-peers as below:
> dial-peer voice 10 pots
> incoming called-number .
> direct-inward-dial
>
>
> port 0/0:D
>
> dial-peer voice 2 voip
> destination-pattern x...<- this is the access number
>
> session target ipv4:x.x.x.x <- this is the IP of the SysMaster GW
>
> Check the following documents for more detail
>
> http://www.cisco.com/en/US/docs/routers/access/as5350/software/configuration/guide/54bas3.html#wpxref17473
>
> http://www.cisco.com/en/US/docs/routers/access/as5350/software/configuration/guide/54voice_ps501_TSD_Products_Configuration_Guide_Chapter.html
>
>
> regards,
>
> 2011/11/15 Цэвээндорж <tseveendorj at gmail.com
> <mailto:tseveendorj at gmail.com>>
>
> Hello,
>
> I don't know how called it technically. Let me try to explain what
> I'm trying to do.
> I have SysMaster SM7000 gateway and billing also. I cannot connect
> to PSTN via E1 with R2 signaling. I thought I cannot configure
> sysmaster correctly then I ask from sysmaster guys but reply as follow
>
> Basically, we can support this requirement you have but NOT on
> the current HW you have.
>
> If you need to support MFC/R2 signaling with your current
> SM7000, then it will cost you just as much for custom
> development as it would to just purchase a new SM7000 GW that
> can support it already.
>
>
> Now let's begin
> I have cisco gateway AS5350XM (Version 12.4(20)T1) with 4xE1 card
> using current system. I'm planning interconnect to PSTN with cisco
> gateway +1xE1 with R2 signaling. My topology looks like this.
>
> Access number ---> PSTN ----------E1--------> Cisco gateway
> without IVR ----------TCP/IP---------> Sysmaster gateway with IVR
>
> I don't know how to configure when user dials to Access number
> (example 1626) then Cisco gateway without IVR receive request and
> immediately send to Sysmaster gateway with IVR and customer should
> hear the IVR.
>
>
> Any help will be appreciated.
>
> Regards,
> Tseveen.
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net <mailto:cisco-voip at puck.nether.net>
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20111115/4473093d/attachment.html>
More information about the cisco-voip
mailing list