[cisco-voip] Integrating Valcom paging equipment into Cisco based environments..

[Ted Nugent]

Show inventory or show diag

On Thu, Jan 19, 2012 at 11:06 AM, Tim Reimers <treimers at ashevillenc.gov>wrote:

> yeah, that was my read too…****
>
> ** **
>
> The first type “PABX loop trunk” appears that it would work with an FXO **
> **
>
> If I had a spare port I’d just jump on that.. but I don’t, so am hoping to
> avoid buying one, if some other connection in that thing would work…****
>
> ** **
>
> Then I saw that “Page port” type of access.****
>
> Reading and trying to interpret old-telco language, it would appear that
> the page port requires some sort of dry contact closures, etc****
>
> which a router/ATA most certainly do not do.****
>
> So an FXO may be the option of the day…****
>
> ** **
>
> ** **
>
> So here’s the other question –****
>
> (I have some FXO cards in various remote routers, but don’t know exactly
> what they are)****
>
> ** **
>
> How does one go about figuring out whether an FXO port (via commandline)
> is a VIC2-XXX or VIC-XXX ??****
>
> I can see FXO ports via ‘sh ver’ or ‘sh hardware’****
>
> ** **
>
> but I don’t know how to determine what type of FXO they are -- ****
>
> ** **
>
> ** **
>
> ** **
>
> ** **
>
> ** **
>
> ** **
>
> *From:* JoeA [mailto:jalbertini at ymail.com]
> *Sent:* Thursday, January 19, 2012 10:58 AM
> *To:* Tim Reimers
> *Subject:* Re: [cisco-voip] Integrating Valcom paging equipment into
> Cisco based environments..****
>
> ** **
>
> Indeed, this one looks different.  From my reading, looks like only an FXO
> will work.  In the PBXA configuration, it is still referencing a trunk
> connection, not station.  I beleive you will need an FXO port for this to
> work.
>
> ****
>
> ** **
>
> *From:* Tim Reimers <treimers at ashevillenc.gov>
> *To:* JoeA <jalbertini at ymail.com>
> *Sent:* Thursday, January 19, 2012 10:39 AM
> *Subject:* RE: [cisco-voip] Integrating Valcom paging equipment into
> Cisco based environments..****
>
> ** **
>
> I had already tried one, and it doesn’t work….****
>
>  ****
>
> I don’t know if I need to set some jumpers or something on the Valcom or
> what—****
>
>  ****
>
> We have the V-9997 most places, but this site has the V1101a which could
> be different?****
>
>  ****
>
> thanks, Tim****
>
>  ****
>
>  ****
>
>  ****
>
> *From:* JoeA [mailto:jalbertini at ymail.com <jalbertini at ymail.com>]
> *Sent:* Thursday, January 19, 2012 10:02 AM
> *To:* Tim Reimers
> *Subject:* Re: [cisco-voip] Integrating Valcom paging equipment into
> Cisco based environments..****
>
>  ****
>
> Hi Tim,****
>
>  ****
>
> You should be good to go with an FXS.  I have configured FXS and FXO for
> the Valcoms with no issues.****
>
>  ****
>
> Regards,****
>
> Joe****
>
>  ****
>
> *From:* Tim Reimers <treimers at ashevillenc.gov>
> *To:* cisco-voip at puck.nether.net
> *Sent:* Wednesday, January 18, 2012 8:38 PM
> *Subject:* [cisco-voip] Integrating Valcom paging equipment into Cisco
> based environments..****
>
> ** **
>
> Hi all -****
>
>  ****
>
> I have a need to connect a Valcom V-1101A single zone paging controller to
> a Cisco UCM based system.****
>
> http://www.valcom.com/pdf/v-1101a.pdf****
>
>  ****
>
> Does anyone have any experience in selecting the right hardware on the
> Cisco side ?****
>
>  ****
>
> The device refers to the following features:****
>
>  ****
>
>
> • Electronic key system line key access
> • PABX loop trunk port access
> • 1A2 line button access
> • 1A2 intercom access
> • Page port access****
>
>  ****
>
> I think they may be using it as  the "key system line" since that's what
> they had before.****
>
>  ****
>
> I'm not sure what a "1A2" line button is -- but it sounds rather like an
> FXS might handle it- aka an ATA would do it, acting as an FXS port to the
> paging controller.****
>
>  ****
>
>  ****
>
> It also sounds like I could perhaps use an FXO port with the "PABX loop
> trunk port"****
>
> But, I'd rather not purchase an FXO card unless there's no other option
> off that list that would work.****
>
>  ****
>
> I do have ATAs controlling other types of Valcom paging controllers****
>
> like this one, I think ****
>
> http://www.valcom.com/pdf/v-9937.pdf****
>
> which do work with ATAs...****
>
> Does anyone have a clue as to whether the V-1101A can do the same thing??*
> ***
>
>  ****
>
> thanks, Tim****
>
>  ****
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip****
>
> ** **
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20120119/4e7e5e60/attachment.html>