[cisco-voip] Calls to DS-'s across channelized T1, no calling number at CPE

Jonathan Charles jonvoip at gmail.com
Fri Jul 6 21:21:05 EDT 2012


They are set to FXS, they won't send digits... (it is acting like a station
port...)

You will need to set them to FGD or FXO...

ds0-group 0 timeslots 1-2 type fgd-eana



Jonathan

On Fri, Jul 6, 2012 at 1:18 PM, Joseph Mays <mays at win.net> wrote:

> **
> I'm configuring an AS5400 to provide a channelized t1 to an IAD2400. 4 of
> the channels on the T1 are being used for a DS0 group across which we want
> the AS5400 to handle voice calls to and from the IAD2400.
>
> On the AS5400
>
> controller T1 1/0:24
>  framing esf
>  channel-group 0 timeslots 1-20 speed 64
>  loopback network ignore
>  ds0-group 20 timeslots 21-24 type fxs-ground-start
> !
> interface Serial1/0:24:0
>  ip address 216.24.2.5 255.255.255.252
>  no cdp enable
> !
> voice-port 1/0:24:20
> !
> dial-peer voice 248 pots
>  description ATA-8 TEST line 2, WinNETPBX
>  incoming called-number 502567301[1-9]
>  destination-pattern 502567301[1-9]
>  direct-inward-dial
>  port 1/0:24:20
>  forward-digits all
>
> On the IAD2400
>
> controller T1 0/0
>  mode cas
>  framing esf
>  linecode b8zs
>  channel-group 0 timeslots 1-20 speed 64
>  ds0-group 20 timeslots 21-24 type fxo-ground-start
> !
> interface Serial0/0:0
>  ip address 216.24.2.6 255.255.255.252
> !
> voice-port 0/0:20
> !
> voice-port 2/0
>  station-id number 5025673011
> !
> dial-peer voice 10 pots
>  incoming called-number 5025673011
>  direct-inward-dial
>  port 2/0
>  forward-digits all
>
> Calls come in to the 5400 and seem to get sent to the 2400, but there they
> fail (with a beep), apparently not matching a dial-peer. Debug dialpeer on
> the IAD2400 shows that received from the 5400 does not seem to contain a
> called-number. I assume this is why the dialpeer on the 2400 is not being
> matched.
>
> *Mar  2 00:45:29.869: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
>    Calling Number=, Called Number=, Voice-Interface=0x64868BD8,
>    Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search
> Type=PEER_TYPE_VOICE,
>    Peer Info Type=DIALPEER_INFO_SPEECH
> *Mar  2 00:45:29.869: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
>    Match Rule=DP_MATCH_PORT;
> *Mar  2 00:45:29.869: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
>    Result=Failed(-1) after DP_MATCH_PORT
> *Mar  2 00:45:29.869:
> //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerSPI:exit at 5931
>
> Has anyone here set up a 5400 to provide DS0 loops for calling? If so, can
> I see an example config that does this? And any idea why no called number
> seems to be sent to the IAD2400?
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20120706/320d7a1f/attachment.html>


More information about the cisco-voip mailing list