[cisco-voip] Question about what I'm doing wrong trying to block these calls on H.323 ??
miken miken
miken at sisna.com
Fri May 4 12:46:46 EDT 2012
Hello Tim
Your profile has been configured as incoming on your dial-peer for CUCM. In
other words, this will catch the digits inbound from CUCM and not the PRI.
Try configuring the profile incoming on your inbound dial-peer from the
PRI. If you don't have one configured and are using the implicit dial-peer
0, then perhaps adding it to the voice-port may work with out having to
make additional dial-peer changes to your working configuration.
Thank you
MikeN
On Fri, May 4, 2012 at 9:15 AM, Tim Reimers <treimers at ashevillenc.gov>wrote:
> *Hi all -*
>
> * *
>
> *I’m having some difficulty in getting call blocking to work –*
>
> *Calls from 8282438594 to 8282595512 still get through.*
>
> *AT&T gives me “8282438594” as my incoming number, and delivers “5512” as
> my called number.*
>
> * *
>
> * *
>
> *Per*
>
> *
> http://www.cisco.com/en/US/customer/tech/tk652/tk90/technologies_configuration_example09186a00803f818a.shtml#con13
> *
>
> *I’ve done the steps in that section.*
>
> * *
>
> *Only difference is that I’m using a VOIP dialpeer and they show POTS
> peers.*
>
> *The syntax at the top of the section does seem to indicate that either
> “pots|voip”*
>
> *would be legal syntax though.*
>
> * *
>
> *Here’s the setup –*
>
> * *
>
> *ISDN PRI connecting to UCM via H.323*
>
> *Router running *
>
> *c2800nm-spservicesk9-mz.123-11.T8.bin*
>
> * *
>
> *UCM is version 7.15*
>
> * *
>
> * *
>
> *Here’s my setup*
>
> ** **
>
> ** **
>
> ** **
>
> voice translation-profile call_block****
>
> translate calling 2****
>
> ** **
>
> ** **
>
> voice translation-rule 2****
>
> rule 1 reject /8282438594/****
>
> !****
>
> !****
>
> !****
>
> ** **
>
> ** **
>
> ** **
>
> dial-peer voice 1000 voip****
>
> description Inbound from PRI to Callmanager2****
>
> *call-block translation-profile incoming call_block*
>
> *call-block disconnect-cause incoming call-reject*
>
> preference 1****
>
> destination-pattern [2-8]...****
>
> progress_ind setup enable 3****
>
> modem passthrough nse codec g711ulaw****
>
> voice-class codec 1****
>
> voice-class h323 1****
>
> session target ipv4:192.168.201.6****
>
> incoming called-number .****
>
> dtmf-relay h245-alphanumeric****
>
> fax rate disable****
>
> no vad****
>
> !****
>
> dial-peer voice 1001 voip****
>
> description Inbound from PRI to Callmanager1****
>
> *call-block translation-profile incoming call_block*
>
> *call-block disconnect-cause incoming call-reject*
>
> preference 2****
>
> destination-pattern [2-8]...****
>
> progress_ind setup enable 3****
>
> modem passthrough nse codec g711ulaw****
>
> voice-class codec 1****
>
> voice-class h323 1****
>
> session target ipv4:192.168.200.2****
>
> incoming called-number .****
>
> dtmf-relay h245-alphanumeric****
>
> fax rate disable****
>
> no vad****
>
> ** **
>
> ** **
>
> * *
>
> *Here’s a debug ISDN Q931 –*
>
> * *
>
> *Looks like I’ve got the right “calling number” set- *
>
> ** **
>
> ** **
>
> CityHall2821#****
>
> 002283: 10w2d: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x1CC6*
> ***
>
> Bearer Capability i = 0x8090A2****
>
> Standard = CCITT****
>
> Transer Capability = Speech****
>
> Transfer Mode = Circuit****
>
> Transfer Rate = 64 kbit/s****
>
> Channel ID i = 0xA98382****
>
> Exclusive, Channel 2****
>
> Progress Ind i = 0x8283 - Origination address is non-ISDN****
>
> Calling Party Number i = 0x2183, '8282438594'****
>
> Plan:ISDN, Type:National****
>
> Called Party Number i = 0x80, '5512'****
>
> Plan:Unknown, Type:Unknown****
>
> 002284: 10w2d: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref =
> 0x9CC6****
>
> Channel ID i = 0xA98382****
>
> Exclusive, Channel 2****
>
> CityHall2821#****
>
> ** **
>
> ** **
>
> *Dialplan testing seems to indicate that the call is hitting the
> dial-peers where I’ve got that translation profile configured.*
>
> ** **
>
> ** **
>
> CityHall2821#sh dialplan number 8282438594****
>
> Macro Exp.: 8282438594****
>
> ** **
>
> VoiceOverIpPeer1000****
>
> peer type = voice, information type = voice,****
>
> description = `Inbound from PRI to Callmanager2',****
>
> tag = 1000, destination-pattern = `[2-8]...',****
>
> answer-address = `', preference=1,****
>
> CLID Restriction = None****
>
> CLID Network Number = `'****
>
> CLID Second Number sent****
>
> CLID Override RDNIS = disabled,****
>
> source carrier-id = `', target carrier-id = `',****
>
> source trunk-group-label = `', target trunk-group-label = `',****
>
> numbering Type = `unknown'****
>
> group = 1000, Admin state is up, Operation state is up,****
>
> incoming called-number = `.', connections/maximum = 6/unlimited,**
> **
>
> DTMF Relay = enabled,****
>
> modem transport = passthrough, nse, payload type = 100, codec =
> g711ulaw,****
>
> ,****
>
> URI classes:****
>
> Incoming (Called) =****
>
> Incoming (Calling) =****
>
> Destination =****
>
> huntstop = disabled,****
>
> in bound application associated: 'DEFAULT'****
>
> out bound application associated: ''****
>
> dnis-map =****
>
> permission :both****
>
> incoming COR list:maximum capability****
>
> outgoing COR list:minimum requirement****
>
> Translation profile (Incoming):****
>
> Translation profile (Outgoing):****
>
> incoming call blocking:****
>
> translation-profile = `call_block'****
>
> disconnect-cause = `call-reject'****
>
> advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily
> 4****
>
> type = voip, session-target = `ipv4:192.168.201.6',****
>
> technology prefix:****
>
> settle-call = disabled****
>
> ip media DSCP = ef, ip signaling DSCP = af31,****
>
> ip video rsvp-none DSCP = af41,ip video rsvp-pass DSCP = af41****
>
> ip video rsvp-fail DSCP = af41,****
>
> UDP checksum = disabled,****
>
> session-protocol = cisco, session-transport = system,****
>
> req-qos = best-effort, acc-qos = best-effort,****
>
> req-qos video = best-effort, acc-qos video = best-effort,****
>
> req-qos audio def bandwidth = 64, req-qos audio max bandwidth = 0,
> ****
>
> req-qos video def bandwidth = 384, req-qos video max bandwidth = 0,
> ****
>
> dtmf-relay = h245-alphanumeric,****
>
> RTP dynamic payload type values: NTE = 101****
>
> Cisco: NSE=100, fax=96, fax-ack=97, dtmf=121, fax-relay=122****
>
> CAS=123, ClearChan=125, PCM switch over u-law=0,A-law=8****
>
> G726r16 using static payload****
>
> G726r24 using static payload****
>
> RTP comfort noise payload type = 19****
>
> fax rate = disable, payload size = 20 bytes****
>
> fax protocol = system****
>
> fax-relay ecm enable****
>
> fax NSF = 0xAD0051 (default)****
>
> codec = g729r8, payload size = 20 bytes,****
>
> Media Setting = flow-through (global)****
>
> Expect factor = 10, Icpif = 20,****
>
> Playout Mode is set to adaptive,****
>
> Initial 60 ms, Max 250 ms****
>
> Playout-delay Minimum mode is set to default, value 40 ms****
>
> Fax nominal 300 ms****
>
> Max Redirects = 1, signaling-type = cas,****
>
> VAD = disabled, Poor QOV Trap = disabled,****
>
> Source Interface = NONE****
>
> voice class sip url = system,****
>
> voice class sip rel1xx = system,****
>
> redirect ip2ip = disabled****
>
> probe disabled,****
>
> voice class perm tag = `'****
>
> Time elapsed since last clearing of voice call statistics never***
> *
>
> Connect Time = 1206442855, Charged Units = 0,****
>
> Successful Calls = 116450, Failed Calls = 4153, Incomplete Calls =
> 3084****
>
> Accepted Calls = 159, Refused Calls = 862,****
>
> Last Disconnect Cause is "10 ",****
>
> Last Disconnect Text is "normal call clearing (16)",****
>
> Last Setup Time = 628057673.****
>
> Matched: 8282438594 Digits: 1****
>
> Target: ipv4:192.168.201.6****
>
> ** **
>
> VoiceOverIpPeer1001****
>
> peer type = voice, information type = voice,****
>
> description = `Inbound from PRI to Callmanager1',****
>
> tag = 1001, destination-pattern = `[2-8]...',****
>
> answer-address = `', preference=2,****
>
> CLID Restriction = None****
>
> CLID Network Number = `'****
>
> CLID Second Number sent****
>
> CLID Override RDNIS = disabled,****
>
> source carrier-id = `', target carrier-id = `',****
>
> source trunk-group-label = `', target trunk-group-label = `',****
>
> numbering Type = `unknown'****
>
> group = 1001, Admin state is up, Operation state is up,****
>
> incoming called-number = `.', connections/maximum = 0/unlimited,**
> **
>
> DTMF Relay = enabled,****
>
> modem transport = passthrough, nse, payload type = 100, codec =
> g711ulaw,****
>
> ,****
>
> URI classes:****
>
> Incoming (Called) =****
>
> Incoming (Calling) =****
>
> Destination =****
>
> huntstop = disabled,****
>
> in bound application associated: 'DEFAULT'****
>
> out bound application associated: ''****
>
> dnis-map =****
>
> permission :both****
>
> incoming COR list:maximum capability****
>
> outgoing COR list:minimum requirement****
>
> Translation profile (Incoming):****
>
> Translation profile (Outgoing):****
>
> incoming call blocking:****
>
> translation-profile = `call_block'****
>
> disconnect-cause = `call-reject'****
>
> advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily
> 4****
>
> type = voip, session-target = `ipv4:192.168.200.2',****
>
> technology prefix:****
>
> settle-call = disabled****
>
> ip media DSCP = ef, ip signaling DSCP = af31,****
>
> ip video rsvp-none DSCP = af41,ip video rsvp-pass DSCP = af41****
>
> ip video rsvp-fail DSCP = af41,****
>
> UDP checksum = disabled,****
>
> session-protocol = cisco, session-transport = system,****
>
> req-qos = best-effort, acc-qos = best-effort,****
>
> req-qos video = best-effort, acc-qos video = best-effort,****
>
> req-qos audio def bandwidth = 64, req-qos audio max bandwidth = 0,
> ****
>
> req-qos video def bandwidth = 384, req-qos video max bandwidth = 0,
> ****
>
> dtmf-relay = h245-alphanumeric,****
>
> RTP dynamic payload type values: NTE = 101****
>
> Cisco: NSE=100, fax=96, fax-ack=97, dtmf=121, fax-relay=122****
>
> CAS=123, ClearChan=125, PCM switch over u-law=0,A-law=8****
>
> G726r16 using static payload****
>
> G726r24 using static payload****
>
> RTP comfort noise payload type = 19****
>
> fax rate = disable, payload size = 20 bytes****
>
> fax protocol = system****
>
> fax-relay ecm enable****
>
> fax NSF = 0xAD0051 (default)****
>
> codec = g729r8, payload size = 20 bytes,****
>
> Media Setting = flow-through (global)****
>
> Expect factor = 10, Icpif = 20,****
>
> Playout Mode is set to adaptive,****
>
> Initial 60 ms, Max 250 ms****
>
> Playout-delay Minimum mode is set to default, value 40 ms****
>
> Fax nominal 300 ms****
>
> Max Redirects = 1, signaling-type = cas,****
>
> VAD = disabled, Poor QOV Trap = disabled,****
>
> Source Interface = NONE****
>
> voice class sip url = system,****
>
> voice class sip rel1xx = system,****
>
> redirect ip2ip = disabled****
>
> probe disabled,****
>
> voice class perm tag = `'****
>
> Time elapsed since last clearing of voice call statistics never***
> *
>
> Connect Time = 85227, Charged Units = 0,****
>
> Successful Calls = 18, Failed Calls = 1061, Incomplete Calls = 0**
> **
>
> Accepted Calls = 0, Refused Calls = 0,****
>
> Last Disconnect Cause is "1 ",****
>
> Last Disconnect Text is "unassigned number (1)",****
>
> Last Setup Time = 627628824.****
>
> Matched: 8282438594 Digits: 1****
>
> Target: ipv4:192.168.200.2****
>
> ** **
>
> CityHall2821#****
>
> ** **
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20120504/5fea9fb9/attachment.html>
More information about the cisco-voip
mailing list