[cisco-voip] NFAS and Dial-Peers

[Divin John (dijohn)]

Hey Nate,

controller T1 0/0/0
cablelength long 0db
pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 0
!
controller T1 0/1/0
cablelength long 0db
pri-group timeslots 1-24 nfas_d backup nfas_int 1 nfas_group 0
!
Can you create:

dial-peer voice 100 pots
destination-pattern 9T
port 0/0/0:D   where 0/0/0 is your Primary NFAS.


Regards,
Divin





On 20/08/13 8:21 PM, "Nate VanMaren" <VanMarenNP at ldschurch.org> wrote:

>So the question is, can I just create a dial-peer pointed to 0/0/0:23
>which is my primary D channel in the NFAS group and it will distribute
>the calls across all members?  Yes
>
>-----Original Message-----
>From: cisco-voip [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of
>Tim Franklin
>Sent: Tuesday, August 20, 2013 7:55 AM
>To: cisco-voip at puck.nether.net
>Subject: [cisco-voip] NFAS and Dial-Peers
>
>So I've got an NFAS setup in my lab and would like to just confirm
>something around dial-peers. According to the cisco documentation I
>should be creating a dial-peer referencing the port:D. However the
>router will not let me do that.
>
>Documentation example:
>http://www.cisco.com/en/US/docs/ios/voice/isdn/configuration/guide/vi_nfas
>_dch_bkup.pdf
>The following example shows configuration of a POTS dial peer with the
>primary controller of an NFAS
>group:
>dial-peer voice 35 pots
>incoming called-number 45...
>destination-pattern 35...
>direct-inward-dial
>port 1/0/0:D
>prefix 35
>
>My configuration is as follows:
>card type t1 0 0
>card type t1 0 1
>!
>network-clock-participate wic 0
>network-clock-participate wic 1
>network-clock-select 1 T1 0/0/0
>network-clock-select 2 T1 0/1/0
>!
>controller T1 0/0/0
>cablelength long 0db
>pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 0
>!
>controller T1 0/1/0
>cablelength long 0db
>pri-group timeslots 1-24 nfas_d backup nfas_int 1 nfas_group 0
>!
>voice-port 0/0/0:23
>!
>voice-port 0/1/0:23
>!
>interface Serial0/0/0:23
>no ip address
>encapsulation hdlc
>isdn switch-type primary-ni
>isdn incoming-voice voice
>no cdp enable
>
>TL;DR
>So the question is, can I just create a dial-peer pointed to 0/0/0:23
>which is my primary D channel in the NFAS group and it will distribute
>the calls across all members?
>Example:
>dial-peer voice 100 pots
>destination-pattern 9T
>port 0/0/0:23
>
>Thanks.
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
> NOTICE: This email message is for the sole use of the intended
>recipient(s) and may contain confidential and privileged information. Any
>unauthorized review, use, disclosure or distribution is prohibited. If
>you are not the intended recipient, please contact the sender by reply
>email and destroy all copies of the original message.
>
>
>_______________________________________________
>cisco-voip mailing list
>cisco-voip at puck.nether.net
>https://puck.nether.net/mailman/listinfo/cisco-voip