[cisco-voip] dspfarm profile 1 conference video homogenous
Pavan K
pav.ccie at gmail.com
Fri Jun 6 18:07:39 EDT 2014
Jason,
I don't think IBS was implemented in CME. it was implemented in UCM 7.0 if
I am not mistaken.
Pavan
On Jun 6, 2014 5:00 PM, "Jason Aarons (AM)" <jason.aarons at dimensiondata.com>
wrote:
> Brian, does this CUCM “intelligent bridge selection” hold true for
> CallManager Express 9.1? CME doesn’t appear intelligent enough to even
> consider this profile for usage! See debug ephone hw-conference below.
>
>
>
> I setup a dspfarm profile 1 conf video homo and its active/registered to
> CME 9.1, however my phones can’t do any conferencing (cannot complete
> conference). Right now this is audio only. I have a PVDM3-256 in here and
> a 10 channel PRI.
>
>
>
> Debug sccp all I don’t even see the CME phones trying to use it;
>
>
>
> IOS 15.2.5M
>
>
>
> voice-card 0
>
> voice-service dsp-reservation 40
>
> dspfarm
>
> dsp services dspfarm
>
> !
>
> dspfarm profile 1 conference video homogeneous
>
> codec g729br8
>
> codec g729r8
>
> codec g729abr8
>
> codec g729ar8
>
> codec g711alaw
>
> codec g711ulaw
>
> codec ilbc
>
> codec h264 vga frame-rate 30 bitrate 1mbps
>
> maximum sessions 8
>
> associate application SCCP
>
> !
>
> Show sccp
>
> 2911-CDG#show sccp
>
> SCCP Admin State: UP
>
> Gateway Local Interface: Vlan502
>
> IPv4 Address: 10.82.66.254
>
> Port Number: 2000
>
> IP Precedence: 5
>
> User Masked Codec list: None
>
> Call Manager: 10.82.66.254, Port Number: 2000
>
> Priority: 1, Version: 7.0, Identifier: 1
>
>
>
> V_Conferencing Oper State: ACTIVE - Cause Code: NONE
>
> Active Call Manager: 10.82.66.254, Port Number: 2000
>
> TCP Link Status: CONNECTED, Profile Identifier: 1
>
> Reported Max Streams: 32, Reported Max OOS Streams: 0
>
> Layout: default 1x1
>
> Supported Codec: g729br8, Maximum Packetization Period: 60
>
> Supported Codec: g729r8, Maximum Packetization Period: 60
>
> Supported Codec: g729abr8, Maximum Packetization Period: 60
>
> Supported Codec: g729ar8, Maximum Packetization Period: 60
>
> Supported Codec: g711alaw, Maximum Packetization Period: 30
>
> Supported Codec: g711ulaw, Maximum Packetization Period: 30
>
> Supported Codec: ilbc, Maximum Packetization Period: 120
>
> Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
>
> Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
>
> Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization
> Period: 30
>
> Supported Codec: h264: 2.0 (vga), Frame Rate: 30fps, Bit Rate: 1000-1000
> Kbps
>
> Max MBPS: 72 (x500 MB/s) Max FS: 5 (x256 MBs)
>
> TLS : ENABLED
>
>
>
> show run | begin ephone-dn 7
>
> ephone-dn 7 octo-line
>
> number 9AAA
>
> conference ad-hoc video
>
> !
>
>
>
> show ephone-dn conference ad-hoc
>
> type active inactive numbers
>
> =======================================
>
> Ad-hoc Video 0 8 9AAA
>
> DN tags: 7
>
>
>
>
>
> Here is a debug ephone hw-conference
>
> Jun 6 21:49:20.674: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:20.678: SkinnyHWConfAPI: reqType 12:Hold On
>
> Jun 6 21:49:20.678: skinny_hwconf_video_hold:Hold dn:ch 1:1
>
> Jun 6 21:49:20.678: SkinnyHWConfAPI: reqType 48:Video DN type
>
> Jun 6 21:49:20.682: SkinnyHWConfAPI: reqType 24:Codec Switch
>
> Jun 6 21:49:23.486: SkinnyHWConfAPI: reqType 33:Meetme Opened
>
> Jun 6 21:49:23.862: SkinnyHWConfAPI: reqType 33:Meetme Opened
>
> Jun 6 21:49:23.994: SkinnyHWConfAPI: reqType 33:Meetme Opened
>
> Jun 6 21:49:24.306: SkinnyHWConfAPI: reqType 46:MTP for CAP list
>
> Jun 6 21:49:24.306: skinny_hwconf_preselect_mtp_tag_for_video:DN not
> video cdn 1 cchan 2
>
> Jun 6 21:49:24.306: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:24.306: SkinnyHideAdhocConfNumber for dn=1 chan=2 streamID=0
>
> Jun 6 21:49:27.182: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:27.494: SkinnyHWConfAPI: reqType 23:Codec List
>
> Jun 6 21:49:27.498: Check associated hwconf with callid 3244
>
> Jun 6 21:49:27.498: Unable to associate a dn/chan with callid 3244
>
> Jun 6 21:49:27.498: Check associated hwconf with callid 3243
>
> Jun 6 21:49:27.498: SkinnyHWConfAPI: reqType 24:Codec Switch
>
> Jun 6 21:49:27.498: SkinnyHWConfAPI: reqType 50:Check to Open MM
>
> Jun 6 21:49:27.582: SkinnyHWConfAPI: reqType 19:Bridge Media
>
> Jun 6 21:49:27.582: SkinnyHwconfBridgeMedia:dn = 1, chan 2, phone = 0
> stream 0
>
> Jun 6 21:49:27.582: SkinnyHwconfBridgeMedia:Call not in conference
>
> Jun 6 21:49:28.182: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:28.182: SkinnyHideAdhocConfNumber for dn=1 chan=2 streamID=0
>
> Jun 6 21:49:28.182: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:29.182: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:29.818: SkinnyAddDnToHwConference: phone=0 (dn=1 chan=1
> state=9) (conf_dn=1 conf_chan=2 state=4)
>
> Jun 6 21:49:29.818: SkinnyHWConfAPI: reqType 14:Is Conf
>
> Jun 6 21:49:29.818: SkinnyHWConfAPI: reqType 14:Is Conf
>
> Jun 6 21:49:29.818: SkinnyAddDnToHwConference: New adhoc conference
>
> Jun 6 21:49:29.822: SkinnyHWConfAPI: reqType 1:New Conf
>
> Jun 6 21:49:29.822: skinny_hwconf_new_adhoc_setup_video_call: Audio
> Ad-Hoc call
>
> Jun 6 21:49:29.822: skinny_hwcfb_check_resource: for Audio
>
> Jun 6 21:49:29.822: skinny_hwcfbi_find_next_mtpcb Got MTPCB conference
> type req 52:Audio only as Video Homogenous
>
> Jun 6 21:49:29.822: skinny_hwcfbi_find_next_mtpcb No conference MTPCB
> for device type 52:Audio only Fail
>
> Jun 6 21:49:29.822: skinny_hwconf_new_adhoc_conf_setup: No MTPCB
> resources for Audio Call
>
> Jun 6 21:49:29.822: SkinnyAddDnToHwConference: Adhoc new conference setup
> failed!
>
> Jun 6 21:49:35.182: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
> Jun 6 21:49:36.182: SkinnyHWConfAPI: reqType 17:Is XFR to Conf
>
>
>
>
>
>
>
> R3#show telephony-ser
>
> CONFIG (Version=9.1)
>
> =====================
>
> Version 9.1
>
> Max phoneload sccp version 17
>
> Max dspfarm sccp version 18
>
> Cisco Unified Communications Manager Express
>
> For on-line documentation please see:
>
>
> http://www.cisco.com/en/US/products/sw/voicesw/ps4625/tsd_products_support_series_home.html
>
>
>
> protocol mode default
>
> ip source-address 10.82.66.254 port 2000
>
> ip qos dscp:
>
> ef (the MS 6 bits, 46, in ToS, 0xB8) for media
>
> cs3 (the MS 6 bits, 24, in ToS, 0x60) for signal
>
> af41 (the MS 6 bits, 34, in ToS, 0x88) for video
>
> default (the MS 6 bits, 0, in ToS, 0x0) for serviceservice directed-pickup
>
> no auto-reg-ephone
>
> max-ephones 10
>
> max-dn 10
>
> max-conferences 4 gain -6
>
> dspfarm units 10
>
> dspfarm transcode sessions 10
>
> dspfarm 1 r3-conf
>
> dspfarm 2
>
> dspfarm 3
>
> dspfarm 4
>
> dspfarm 5
>
> dspfarm 6
>
> dspfarm 7
>
> dspfarm 8
>
> dspfarm 9
>
> dspfarm 10
>
> conference hardware
>
> privacy
>
> no privacy-on-hold
>
> hunt-group report delay 1 hours
>
> hunt-group logout DND
>
> max-redirect 10
>
> cnf-file location: system:
>
> cnf-file option: PER-PHONE-TYPE
>
> network-locale[0] US (This is the default network locale for this box)
>
> network-locale[1] US
>
> network-locale[2] US
>
> network-locale[3] US
>
> network-locale[4] US
>
> user-locale[0] US (This is the default user locale for this box)
>
> user-locale[1] US
>
> user-locale[2] US
>
> user-locale[3] US
>
> user-locale[4] US
>
> srst mode auto-provision is OFF
>
> srst ephone template is 0
>
> srst dn template is 0
>
> srst dn line-mode single
>
> phone service webAccess 0
>
> moh music-on-hold.au
>
> time-format 12
>
> date-format mm-dd-yy
>
> secondary-dialtone 9
>
> transfer-pattern .T
>
> keepalive 30 auxiliary 30
>
> timeout interdigit 10
>
> timeout busy 10
>
> timeout ringing 180
>
> timeout transfer-recall 0
>
> timeout ringin-callerid 8
>
> timeout night-service-bell 12
>
> caller-id name-only: enable
>
> web admin system name administrator password ccievoice
>
> web admin customer name Customer
>
> edit DN through Web: enabled.
>
> edit TIME through web: enabled.
>
> background save interval 10 minutes
>
> Log (table parameters):
>
> max-size: 150
>
> retain-timer: 15
>
> create cnf-files version-stamp 7960 Jun 06 2014 21:43:25
>
> transfer-system full-consult
>
> transfer-digit-collect new-call
>
> multicast moh 239.1.1.1 port 2000
>
> local directory service: enabled.
>
> Extension-assigner tag-type ephone-tag.
>
> Call List BLF is enabled
>
>
>
> *From:* bmeade90 at gmail.com [mailto:bmeade90 at gmail.com] *On Behalf Of *Brian
> Meade
> *Sent:* Wednesday, May 28, 2014 7:07 PM
> *To:* Jason Aarons (AM)
> *Cc:* cisco-voip (cisco-voip at puck.nether.net)
> *Subject:* Re: [cisco-voip] dspfarm profile 1 conference video homogenous
>
>
>
>
>
> Jason,
>
>
>
> The non-video phones should be able to use a video conference bridge but
> it will use up DSP resources really fast. I'd suggest having the separate
> audio-only dspfarm profile if possible. The non-video phones will prefer a
> non-video conference bridge by default as part of the Intelligent Bridge
> Selection feature.
>
>
>
> Brian
>
>
>
> On Wed, May 28, 2014 at 6:05 PM, Jason Aarons (AM) <
> jason.aarons at dimensiondata.com> wrote:
>
> Customer is moving from 2811/PVDM2s the 2911/PVD3/15.2. Customer has
> mix of 7965 and 9971 video phones.
>
>
>
> I am planning the PVDM3-128/256/sDSPs need in each 2911.
>
>
> http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmevconf.html#pgfId-1055244
> <<this running-config is for CME but applies to CUCM as well
>
>
>
> They will have a mix of 9971 video/audio and 7965 audio conference using
> Cisco IOS Homogenous Video Conferences.
>
>
>
> Is it necessary in the router and CUCM to configure both of these dspfarm
> profiles or will the video do voice-only calls too?
>
>
>
> dspfarm profile 1 conference video homogenous
>
> codec g729r8
>
> codec g711ulaw
>
> codec h264 vga
>
> max conference-participants 4
>
> max session 6
>
> associate application SCCP
>
> no shut
>
> !
>
> dspfarm profile 2 conference
>
> codec g729r8
>
> codec g711ulaw
>
> max session 6
>
> associate application SCCP
>
> no shut
>
>
>
> In short if I only configure profile 1 is that fine? Can it do both audio
> and video conferneces, say if only 7965 endpoints us it, then it would be
> used for audio only? Or does it have to be a video to for that profile?
>
>
>
> Do I even need to configure profile 2?
>
>
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
>
> itevomcid
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20140606/3cd41cd8/attachment.html>
More information about the cisco-voip
mailing list