[cisco-voip] OSPF Labs

[Ed Leatherman]

Hi Jose, I think you mighta hit the wrong mailing list :)

That said, what output are you trying to catch? on IOS 15.4T I'm getting
some output with the debug ip ospf adj (below).



R1(config-if)#do sh debug

OSPF:
  OSPF adjacency debugging is on

<snip>

R1(config-if)#no shut
R1(config-if)#^Z
R1#
*May 15 11:25:09.890: %SYS-5-CONFIG_I: Configured from console by console
R1#
*May 15 11:25:11.386: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state
to up
*May 15 11:25:12.387: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet0/0, changed state to up
*May 15 11:25:12.387: OSPF-1 ADJ   Et0/0: Route adjust notification: UP/UP
*May 15 11:25:12.387: OSPF-1 ADJ   Et0/0: Interface going Up
*May 15 11:25:12.387: OSPF-1 ADJ   Et0/0: Interface state change to UP, new
ospf state WAIT
R1#
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: 2 Way Communication to 2.2.2.2,
state 2WAY
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Backup seen event before WAIT
timer
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: DR/BDR election
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Elect BDR 1.1.1.1
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Elect DR 2.2.2.2
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Elect BDR 1.1.1.1
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Elect DR 2.2.2.2
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: DR: 2.2.2.2 (Id)   BDR: 1.1.1.1
(Id)
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Nbr 2.2.2.2: Prepare dbase
exchange
*May 15 11:25:14.616: OSPF-1 ADJ   Et0/0: Send DBD to 2.2.2.2 seq 0x9C9 opt
0x52 flag 0x7 len 32
*May 15 11:25:14.623: OSPF-1 ADJ   Et0/0: Rcv DBD from 2.2.2.2 seq 0x1593
opt 0x52 flag 0x7 len 32  mtu 1500 state EXSTART
*May 15 11:25:14.623: OSPF-1 ADJ   Et0/0: NBR Negotiation Done. We are the
SLAVE
*May 15 11:25:14.623: OSPF-1 ADJ   Et0/0: Nbr 2.2.2.2: Summary list built,
size 1
*May 15 11:25:14.623: OSPF-1 ADJ   Et0/0: Send DBD to 2.2.2.2 seq 0x1593
opt 0x52 flag 0x2 len 52
*May 15 11:25:14.624: OSPF-1 ADJ   Et0/0: Rcv DBD from 2.2.2.2 seq 0x1594
opt 0x52 flag 0x1 len 72  mtu 1500 state EXCHANGE
*May 15 11:25:14.624: OSPF-1 ADJ   Et0/0: Exchange Done with 2.2.2.2
*May 15 11:25:14.624: OSPF-1 ADJ   Et0/0: Send LS REQ to 2.2.2.2 length 48
LSA count 2
*May 15 11:25:14.624: OSPF-1 ADJ   Et0/0: Send DBD to 2.2.2.2 seq 0x1594
opt 0x52 flag 0x0 len 32
*May 15 11:25:14.625: OSPF-1 ADJ   Et0/0: Rcv LS UPD from 2.2.2.2 length
104 LSA count 2
*May 15 11:25:14.625: OSPF-1 ADJ   Et0/0: Synchronized with 2.2.2.2, state
FULL
*May 15 11:25:14.625: %OSPF-5-ADJCHG: Process 1, Nbr 2.2.2.2 on Ethernet0/0
from LOADING to FULL, Loading Done
R1#
*May 15 11:25:14.625: OSPF-1 ADJ   Et0/0: Rcv LS REQ from 2.2.2.2 length 36
LSA count 1
R1#
*May 15 11:25:24.243: OSPF-1 ADJ   Et0/0: Neighbor change event
*May 15 11:25:24.243: OSPF-1 ADJ   Et0/0: DR/BDR election
*May 15 11:25:24.243: OSPF-1 ADJ   Et0/0: Elect BDR 1.1.1.1
*May 15 11:25:24.243: OSPF-1 ADJ   Et0/0: Elect DR 2.2.2.2
*May 15 11:25:24.243: OSPF-1 ADJ   Et0/0: DR: 2.2.2.2 (Id)   BDR: 1.1.1.1
(Id)
R1#


On Tue, May 12, 2015 at 9:00 AM, Jose Colon II <jcolon424 at gmail.com> wrote:

> Hey guys, I am running some OSPF labs and I notice that the following
> commands do not provide any output.
>
> debus ip ospf adj
>
> I do however get the desired output from "debug ip ospf events". Is this a
> change in software or is everyone teaching a command that is no longer
> used. I am using a Cisco 1921 and 2901 router as well as Cisco Packet
> Tracer and I still do not get any output from "debug ip ospf adj"
>
> Thanks
> Jose
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>


-- 
Ed Leatherman
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20150515/9f2e74d4/attachment.html>