[cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
Hamu Ebiso
hebiso2010 at hotmail.com
Wed Feb 28 15:46:46 EST 2018
Here is the dial-peer output
1#show run | sec dial-peer
dial-peer voice 1 pots
trunkgroup FXO_EM
translation-profile incoming Inbound
call-block translation-profile incoming block_profile
call-block disconnect-cause incoming call-reject
incoming called-number .
direct-inward-dial
dial-peer voice 911 pots
trunkgroup FXO_EM
description Services
translation-profile outgoing Strip9
destination-pattern 911
dial-peer voice 9911 pots
trunkgroup FXO_EM
description Services
translation-profile outgoing Strip9
destination-pattern 9911
dial-peer voice 2 voip
description CUCM Dial-Peer - Inbound
preference 1
destination-pattern 12086858038
session protocol sipv2
session target ipv4:10.0.2.6
incoming uri via 10
voice-class codec 1
dtmf-relay rtp-nte sip-kpml
fax-relay ecm disable
fax nsf 000000
ip qos dscp cs3 signaling
no vad
dial-peer voice 3 voip
preference 2
destination-pattern 12086858038
session target ipv4:10.0.2.3
dial-peer voice 650 pots
trunkgroup Local
description Local outbound
translation-profile outgoing Strip9
destination-pattern 9208.......
dial-peer voice 4 pots
trunkgroup FXO_EM
description ** 10-digit Local Call **
translation-profile outgoing Strip9
destination-pattern ^9[2-9]..[2-9]......$
forward-digits 10
dial-peer voice 5 voip
description FXO test
destination-pattern 12083437020
session target ipv4:10.0.2.5
thank you very much!!
________________________________
From: Anthony Holloway <avholloway+cisco-voip at gmail.com>
Sent: Wednesday, February 28, 2018 1:29 PM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
Maybe you're actually using MGCP then? You still haven't shown the dial-peers on the gateway. Is that because you don't have any?
show run | section dial-peer
On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:
debug was turned on as shown below.
1#debug voice ccapi inout
voip ccapi inout debugging is on
made test calls and then show log, I see below output.
1#show log
Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: level debugging, 517 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 550 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level debugging, 620 message lines logged
Logging to 10.0.7.139 (udp port 514, audit disabled,
link up),
435 message lines logged,
0 message lines rate-limited,
0 message lines dropped-by-MD,
xml disabled, sequence number disabled
filtering disabled
Logging to 10.0.8.12 (udp port 514, audit disabled,
link up),
435 message lines logged,
0 message lines rate-limited,
0 message lines dropped-by-MD,
xml disabled, sequence number disabled
filtering disabled
Logging Source-Interface: VRF Name:
Loopback0
I don't see any calls activity.
thanks
________________________________
From: Anthony Holloway <avholloway+cisco-voip at gmail.com<mailto:avholloway%2Bcisco-voip at gmail.com>>
Sent: Wednesday, February 28, 2018 11:19 AM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
But you didn't send all the information, because your output doesn't show the dial-peers.
One method is to capture the output from "debug voip ccapi inout" and look for the following line "Outgoing Dial-peer="
You also didn't address the regions either. Can you send that too?
On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:
I was just trying to give you all the information so that you will be able to see the whole picture.
Regarding your questions, I don't know how to check that.
________________________________
From: Anthony Holloway <avholloway+cisco-voip at gmail.com<mailto:avholloway%2Bcisco-voip at gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent everything but.
Do you know how to confirm which dial-peer the gateway is using?
On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2010 at hotmail.com<mailto:hebiso2010 at hotmail.com>> wrote:
Below is gateway configuration
isdn switch-type primary-ni
!
!
trunk group FXO_EM
hunt-scheme sequential
translation-profile incoming Incoming
!
!
trunk group Local
hunt-scheme sequential
translation-profile outgoing outbound
!
!
trunk group LD
translation-profile outgoing outbound
!
voice-card 0
dspfarm
dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
ip address trusted list
ipv4 10.170.99.12
ipv4 10.44.50.14
ipv4 10.44.50.39
no ip address trusted authenticate
clid substitute name
clid network-provided
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redirect ip2ip
signaling forward unconditional
fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
no fax-relay sg3-to-g3
modem passthrough nse codec g711ulaw
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
session transport tcp
min-se 360 session-expires 360
ds0-num
header-passing
error-passthru
registrar server expires max 600 min 60
early-offer forced
midcall-signaling passthru
no call service stop
!
!
voice class uri 10 sip
host ipv4:10.x.x.x
host ipv4:10..x.x.x
host ipv4:10..x.x.x
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
!
voice class codec 2
codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
rule 1 /^208343\(....\)$/ /1208343\1/
!
voice translation-rule 9
rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
rule 1 /^911/ /911/
rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
rule 1 /^911/ /911/
rule 2 /^9911/ /911/
rule 4 /^9\(011.*\)/ /\1/
rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
translate calling 91
translate called 1
!
voice translation-profile Inbound
translate called 1
!
voice translation-profile Strip9
translate called 10
!
voice translation-profile block_profile
translate calling 15
!
voice translation-profile outbound
translate calling 10
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC123128X5
license accept end user agreement
archive
log config
hidekeys
username admin privilege 15 password 7 105D1F0C
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
!
!
controller T1 0/0/0
shutdown
cablelength long 0db
!
controller T1 0/1/0
shutdown
cablelength long 0db
!
!
!
!
!
!
interface Loopback0
ip address 10.x.x.x 255.255.255.128
!
interface GigabitEthernet0/0
description uplink to Lan1
ip address 10.x.x.x 255.255.255.252
duplex auto
speed auto
media-type rj45
!
interface GigabitEthernet0/1
description uplink to Lan2
ip address 10.x.x.x 255.255.255.252
duplex auto
speed auto
media-type rj45
!
router ospf 1
auto-cost reference-bandwidth 10000
network 10.0.0.0 0.0.255.255 area 10.0.0.0
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180228/4446751a/attachment.html>
More information about the cisco-voip
mailing list