[cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

Maybe you're actually using MGCP then?  You still haven't shown the
dial-peers on the gateway.  Is that because you don't have any?

show run | section dial-peer

On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2010 at hotmail.com> wrote:

> debug was turned on as shown below.
>
>
> 1#debug voice ccapi inout
> voip ccapi inout debugging is on
>
> made test calls and then show log, I see below output.
>
> 1#show log
> Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0
> flushes, 0 overruns, xml disabled, filtering disabled)
>
> No Active Message Discriminator.
>
>
> No Inactive Message Discriminator.
>
>
>     Console logging: level debugging, 517 messages logged, xml disabled,
>                      filtering disabled
>     Monitor logging: level debugging, 0 messages logged, xml disabled,
>                      filtering disabled
>     Buffer logging:  level debugging, 550 messages logged, xml disabled,
>                     filtering disabled
>     Exception Logging: size (4096 bytes)
>     Count and timestamp logging messages: disabled
>     Persistent logging: disabled
>
> No active filter modules.
>
>     Trap logging: level debugging, 620 message lines logged
>         Logging to 10.0.7.139  (udp port 514, audit disabled,
>               link up),
>               435 message lines logged,
>               0 message lines rate-limited,
>               0 message lines dropped-by-MD,
>               xml disabled, sequence number disabled
>               filtering disabled
>         Logging to 10.0.8.12  (udp port 514, audit disabled,
>               link up),
>               435 message lines logged,
>               0 message lines rate-limited,
>               0 message lines dropped-by-MD,
>               xml disabled, sequence number disabled
>               filtering disabled
>         Logging Source-Interface:       VRF Name:
>         Loopback0
>
>
> I don't see any calls activity.
>
>
> thanks
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to capture the output from "debug voip ccapi inout" and look
> for the following line "Outgoing Dial-peer="
>
> You also didn't address the regions either.  Can you send that too?
>
> On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2010 at hotmail.com>
> wrote:
>
> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> ------------------------------
> *From:* Anthony Holloway <avholloway+cisco-voip at gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2010 at hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-se 360 session-expires 360
>   ds0-num
>   header-passing
>   error-passthru
>   registrar server expires max 600 min 60
>   early-offer forced
>   midcall-signaling passthru
>   no call service stop
> !
> !
> voice class uri 10 sip
>  host ipv4:10.x.x.x
>  host ipv4:10..x.x.x
>  host ipv4:10..x.x.x
> voice class codec 1
>  codec preference 1 g711ulaw
>  codec preference 2 g729r8
> !
> voice class codec 2
>  codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
>  rule 1 /^208343\(....\)$/ /1208343\1/
> !
> voice translation-rule 9
>  rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
> !
> voice translation-rule 15
> !
> voice translation-rule 30
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
>  rule 4 /^9\(011.*\)/ /\1/
>  rule 9 /^9\(.*\)/ /\1/
> !
> !
> voice translation-profile Add1
>  translate calling 91
>  translate called 1
> !
> voice translation-profile Inbound
>  translate called 1
> !
> voice translation-profile Strip9
>  translate called 10
> !
> voice translation-profile block_profile
>  translate calling 15
> !
> voice translation-profile outbound
>  translate calling 10
> !
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> license udi pid CISCO3845-MB sn FOC123128X5
> license accept end user agreement
> archive
>  log config
>   hidekeys
> username admin privilege 15 password 7 105D1F0C
> username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
> !
> !
> controller T1 0/0/0
>  shutdown
>  cablelength long 0db
> !
> controller T1 0/1/0
>  shutdown
>  cablelength long 0db
> !
> !
> !
> !
> !
> !
> interface Loopback0
>  ip address 10.x.x.x 255.255.255.128
> !
> interface GigabitEthernet0/0
>  description uplink to Lan1
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> interface GigabitEthernet0/1
>  description uplink to Lan2
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> router ospf 1
>  auto-cost reference-bandwidth 10000
>  network 10.0.0.0 0.0.255.255 area 10.0.0.0
> !
> ip forward-protocol nd
> !
> !
> no ip http server
> no ip http secure-server
> !
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20180228/e1311b5d/attachment.html>