[cisco-voip] ATA 186 question

[Carlo Calabrese]

 if money is a big problem. but you could get some ATA187s for about $20 apiece or ATA190s
    On Thursday, January 27, 2022, 02:49:53 PM MST, Lisa Notarianni <lisa.notarianni at scranton.edu> wrote:  
 
 
Thank you all for your quick responses.  We will go beg for funding and replace the ATAs.  We cannot set speed to 10 since it is not an option according to our network engineer.
 
  
 
Lisa
 
From: Lelio Fulgenzi <lelio at uoguelph.ca> 
Sent: Thursday, January 27, 2022 4:26 PM
To: Lisa Notarianni <lisa.notarianni at scranton.edu>
Cc: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] ATA 186 question
 
  
 
  
 
You might want to double check that. From this, 17.3, it shows 10 is a valid option. 
 
  
 
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/17-3/configuration_guide/int_hw/b_173_int_and_hw_9300_cg/configuring_interface_characteristics.html#task_uw1_3wc_g1b
 
Sent from my iPhone
 



 

On Jan 27, 2022, at 3:45 PM, Lisa Notarianni <lisa.notarianni at scranton.edu> wrote:
 


 
 
CAUTION: This email originated from outside of the University of Guelph. Do not click links or open attachments unless you recognize the sender and know the content is safe. If in doubt, forward suspicious emails toIThelp at uoguelph.ca
 
  
 
We just began Cisco switch upgrade to 9300s and ran into an unexpected issue.
 
 
 
We have many ATA 186s out there (about 100) and did not budget for replacement as we were gratefully approved for the massive overhaul of the switches.  This ended up being an unforeseen glitch.
 
 
 
We cannot get the ATA 186s to work on this switch with this IOS version:                              1 65 C9300-48UXM 17.03.04 CAT9K_IOSXE INSTALL
 
However, the 186s are working on this switch with this IOS version:                                         1 64 C9300-48P 16.9.5 CAT9K_IOSXE INSTALL
 
 
 
I know it is not an apples to apples comparison but I was wondering if anyone had a workaround for the newer model/IOS.
 
 
 
We believe the problem is that the ATA186s are hard coded at 10Mbps/half duplex.  Even if we change the switch port parameter from 0x00000000 to 0x000000ff  the ATA will not register.  The switch port is also configured at duplex auto but the slowest we can make the port is 100Mbps.
 
 
 
Is this not possible?  I am hoping you Cisco geniuses have a solution😊
 
 
 
Lisa Notarianni
 
University of Scranton
 
Telecommunications Engineer
 
Infrastructure Services
 
800 Linden St.
 
Scranton PA 18510
 
570.941.4325
 
 
 
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
 
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-voip/attachments/20220128/b3c23069/attachment.htm>