[f-nsp] Not able to use XMR 10 gig linecard

[Dave Peters]

You can try:

lp boot system mp primary

then

power-off lp primary [slot #]
power-on lp primary [slot#]

If that doesn't work, you may want to try loading the compatible software train onto the interactive card, so it matches the management module.

--Dave Peters
________________________________________
From: foundry-nsp-bounces at puck.nether.net [foundry-nsp-bounces at puck.nether.net] On Behalf Of Remco Bressers [remco at signet.nl]
Sent: Tuesday, November 09, 2010 8:44 AM
To: foundry-nsp at puck.nether.net
Subject: Re: [f-nsp] Not able to use XMR 10 gig linecard

We didn't physically remove the module yet (it's 150KM away) so i hoped
there was a different way of doing it.

The boot procedure on the LP is pretty non-explanatory :

telnet at r#lp boot system mp pri 2
telnet at r#rconsole 2
Remote connection to LP slot 2 established
Press CTRL-X or type 'exit' to disconnect it
NetIron XMR/MLX Boot Monitor Version 3.5.00e
Enter 'b' to stop at boot monitor
sent IPC_MSGTYPE_REBOOT to slot 16 (my_slot = 1, ipc_post_rx32_mode = 0)
received IPC_MSGTYPE_REBOOT_ACK from fid d020
REV B LP
get_moass = cf 207  20
ipc_sedule_type: board_clnd_card_boot: module_type = 20
REV B LP
get_module_type: board_class = cf 207  20
PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xgmac_arg = 0,
hv_cam_type = ff, hv_value = 0
sent IPC_MSGTYPE_LP_CARD_BOOT to slot 32
Received IPC_MSGTYPE_MP_CARD_BOOT_INFO
g_bp_board_class_val = 0x86, g_rx16_backplane_type = 255
BOOT INFO: boot interactively
REV B LP
get_module_type: board_class = cf 207  20
REV B LP
get_module_type: board_class = cf 207  20
PPCR type = 2, xtm_arg = 1, xpp_arg = 0, pbif_arg = 0, xbridge_arg = 0,
xgmac_arg = 0, hv_cam_type = ff, hv_value = 0
sent IPC_MSGTYPE_LP_CARD_SW_LOADED (failed) to slot 32

So i think we have to physically eject the module :(

Regards,

Remco



On 11/09/2010 05:41 PM, Jared Valentine wrote:
> Sounds like you need to:
>
> 1.) physically remove module
> 2.) remove slot configuration using "no module xxx"
> 3.) pre-stage the config with the new module "module xxx"
> 3.) physically replace module
> 4.) deal with the software issue
>
> -Jared
>
> -----Original Message-----
> From: foundry-nsp-bounces at puck.nether.net
> [mailto:foundry-nsp-bounces at puck.nether.net] On Behalf Of Remco Bressers
> Sent: Tuesday, November 09, 2010 9:16 AM
> To: foundry-nsp at puck.nether.net
> Subject: Re: [f-nsp] Not able to use XMR 10 gig linecard
>
> Unfortunately that won't work because of the same reason :
>
> telnet at ams-er8-sara(config)#no module 2 ni-xmr-20-port-1g
> Error: Please remove module from slot 2 first
>
> Also, powering off the card won't do.
>
> :(
>
> Regards,
>
> Remco
>
>
> On 11/09/2010 05:12 PM, Michiel Muhlenbaumer wrote:
>> First run 'no module blabla' and then power-off/on the lc.
>>
>> Met vriendelijke groet,
>> Best regards,
>>
>> Michiel Muhlenbaumer
>> Atrato IP Networks
>>
>> (sent from mobile device)
>>
>> On 9 nov. 2010, at 16:58, Remco Bressers <remco at signet.nl> wrote:
>>
>>> Hi,
>>>
>>> The other day, i inserted a brand new NI-XMR-10Gx4 in an XMR-4, but it
>>> won't work correctly.
>>> If i do a "show module", i see the following output on the slot :
>>>
>>> S2: NI-XMR-10Gx4 4-port 10GbE Module  CARD_STATE_INTERACTIVE    20
>>> 0012.f2f5.d128
>>> (S2: Configured as NI-XMR-1Gx20-SFP 20-port 1GbE/100FX Module)
>>>
>>> What is the correct procedure to configure S2 as ni-xmr-10gx4 ?
>>>
>>> I tried :
>>>
>>> telnet at r(config)#module 2 ni-xmr-4-port-10g
>>> Error: Please remove module from slot 2 first
>>> telnet at r(config)#
>>>
>>> Is this the only (and correct) way?
>>>
>>> --
>>> Kind regards,
>>> Signet bv
>>>
>>> Remco Bressers
>>> _______________________________________________
>>> foundry-nsp mailing list
>>> foundry-nsp at puck.nether.net
>>> http://puck.nether.net/mailman/listinfo/foundry-nsp
>
>


--
Met vriendelijke groet,
Signet bv


Remco Bressers

T 040 - 707 4 907
F 040 - 707 4 909
E rbressers at signet.nl
altijd online? www.signet.nl
_______________________________________________
foundry-nsp mailing list
foundry-nsp at puck.nether.net
http://puck.nether.net/mailman/listinfo/foundry-nsp